JBL Speaker CONTROL 25AV WH User Manual

®
Shielded Indoor/Outdoor  
Monitor Speaker  
Control 25AV  
Professional Series  
Key Features:  
Video shielded for use near video  
monitors.  
Extremely smooth frequency response.  
Stainless steel grille for harsh  
environments.  
60 Watt transformer for 70V or 100V  
lines, with 8thru.  
TM  
SonicGuard overload protection.  
130 mm (5¼") polypropylene coated  
woofer, 10 mm (¾") titanium coated  
horn-loaded tweeter.  
Includes InvisiBall® mounting  
hardware and sealed input panel cover.  
Screw-down input terminals.  
100° x 100° high frequency horn.  
®
The Control 25AV utilizes a deep  
cabinet, high power components and  
complex network to achieve extremely  
smooth high fidelity performance from a  
compact 2-way loudspeaker.  
Premium performance capability and  
even coverage ensures excellent sound  
quality throughout the listening area.  
Specifications:  
1
Freq. Range (-10 dB) : 70 Hz - 23 kHz  
2
Midrange ( 1.5 dB, typical) : 130 Hz - 14 kHz  
3
100 Hr Power Capacity : 200 Watts Continuous Program Power  
100 Watts Continuous Pink Noise  
Nominal Coverage: 100° x 100°  
Nominal Sensitivity : 87 dB SPL, 1W @ 1 m (3.3ft)  
Nominal Coverage: 100° x 100°  
4
Maximum SPL @ 1m: 113 dB continuous peak pink noise  
107 dB continuous average pink noise  
Magnetic shielding allows use of the  
speaker in close proximity to video moni-  
tors.  
The top-quality transformer, with  
reduced saturation, allows use on either  
70 volt or 100 volt distributed speaker  
lines, with similar performance fidelity. In  
the bypass position, the high 8imped-  
ance allows use of more speakers on a  
loudspeaker line.  
103 dB continuous average music or speech  
Directivity Factor (Q): 4.9, averaged 500 Hz to 4 kHz  
Directivity Index (DI): 6.9 dB, averaged 500 Hz to 4 kHz  
Nominal Impedance: 8 ohms  
Minimum Impedance: 6.7 ohms at 230 Hz  
Crossover Type: Second Order Lowpass, Second Order Highpass, Complex  
Optimization for Maximally Flat Response  
Transformer Taps: 170V: 60W, 30W, 15W, 7.5W taps (Taps #4,#3, #2 & #1)  
100V: 60W, 30W, 15W taps (Taps #3, #2, & #1)  
Thru position: 8nominal  
Transducers:  
Physical:  
Low-Frequency: 130 mm (5.25 in) polypropylene-coated paper with WeatherEdge  
surround, 25 mm (1 in) voicecoil on kapton former  
High-Frequency: 20 mm (.75 in) titanium coated PEI  
The unique, global patent pending  
®
InvisiBall mounting method is simple to  
install, aims easily, and provides a high  
degree of theft deterrence.  
Enclosure Material: High Impact polystyrene  
Grille: Painted stainless steel, black or white to match cabinet, paintable  
Overload Protection: Full-range power limiting to protect network and transducers. Internal  
fuse to protect during exceptional overload condition  
The cabinet accepts a variety of paints  
to match any décor.  
Weather resistance is maximized by a  
stainless steel grille, which is paintable.  
Coating the woofer in polypropylene and  
terminating its circumference in JBL’s  
WeatherEdgeTM, a seamless, butyl rubber  
extension of the woofer surround, pro-  
tects critical transducer elements. The  
polycarbonate tweeter diaphragm is rein-  
forced with a thin film of titanium for  
added rigidity and endurance. Nickel/zinc  
rust-resistant terminals ensure a secure  
input connection.  
JBL’s exclusive SonicGuard overload  
protection is virtually inaudible to the lis-  
tener, ensuring reliability while providing  
full fidelity sound.  
The Control 25AV can be used full  
range or low frequencies can be further  
augmented with the addition of one of  
the Control Contractor subwoofer models.  
Environmental: Exceeds Mil Spec 810 for humidity, salt spray, temperature & UV. IEC  
529 IP-X4 splashproof rating  
Termination: Screw-down terminal strip, zinc-plated copper base, nickel plated  
metal screws/washers, accepts up to 9 mm outside 4 mm inside open  
lug (#6, #8 or #10), plus bare wire. (up to 12 AWG)  
Safety Agency Rating: Transformer is listed per UL1876  
Colors: Black or white (-WH)  
Rotation: Against wall on InvisiBall Base: 37° vertical 44° horizontal  
On bracket: 44° all directions  
Dimensions (H x W x D): 236 x 186 x 159 mm (9.3 x 7.4 x 6.3 in)  
Net Weight (ea): 4.0 kg (9 lbs)  
Shipping Weight (pair): 9.0 kg (20 lbs) per pair  
Included Accessories: 1 Pr MTC-PC input panel cover, InvisiBall mounting base, 6 mm x 100  
mm InvisiBall hex wrench  
Optional Accessories: MTC-25V for vertical columnar mounting of up to 3 speakers  
MTC-25/23H for horizontal splaying of 2 speakers. Three brackets  
array either 3 or 6 speakers in a hanging array module for 360°  
horizontal coverage.  
MTC-28/25CM to install speaker down from the ceiling.  
Check JBL Control Contractor Bracket and Adapter Handbook.  
MTC-xxWMG WeatherMax™ Stainless Steel Grille with a three-layer  
backing, including vapor barrier to break up driving precipitation.  
Available in black or white (-WH).  
1
2
In half-space (on wall).  
In full-space  
3
Continuous Pink Noise rating is IEC-shaped pink noise with a 6 dB crest factor for 100 hours continuously.  
Continuous program power is a conservative expression of the system’s ability to handle normal speech and music  
program material and is defined as 3 dB above the Continuous Pink Noise Rating.  
4
Half-space (on wall) averaged 100 Hz to 10 kHz.  
Available in black or white (-WH)  
JBL continually engages in research related to product improvement. Changes introduced into existing products with-  
out notice are an expression of that philosophy.  
 
Horizontal 1/3 Octave Polars  
Architectural Specifications:  
The loudspeaker shall consist of a 135 mm (5-1/4 in) low frequency  
transducer, 20 mm (3/4 in) high frequency transducer, and frequency  
dividing network installed in ported enclosure. The low frequency voice  
coil shall be 25 mm (1 in) in diameter.  
Performance specifications of a typical unit shall be as follows: Usable  
frequency response shall extend from 70 Hz to 23 kHz (10 dB below  
rated sensitivity, in half-space, with no external equalization) and the  
speaker shall be flat from 130 Hz to 14 kHz (typically 1.5 dB). Rated  
power shall be at least 200 watts continuous program power for 100  
continuous hours duration (defined a 3 dB above a test signal of filtered  
random pink noise conforming to international standard IEC268-5).  
Measured sensitivity shall be at least 87 dB-SPL (at 1m [3.3ft] with 2.83V  
input, averaged from 100 Hz to 10 kHz).  
The input shall be switchable for use either at nominal 8 ohms, or on  
a 70.7V or 100V distributed speaker line via a built-in 60W transformer.  
Selectable taps shall allow operation nominally at 15W, 30W or 60W  
from either a 70.7V or 100V distributed speaker line, plus 7.5W from a  
70.7V line only.  
The system shall be protected against damage from occasional over-  
powering via full range limiting that limits the power to the network and  
transducers. The limiting system shall be inaudible during activation. The  
high frequency transducer shall be horn-loaded to more evenly cover a  
nominal 90° horizontal by 90° vertical area.  
The enclosure shall be constructed of high-impact polystyrene and the  
grille shall be made of treated stainless steel for protection against the  
elements in outdoor applications, and for easy paintability of both cabi-  
net and grille. The grille shall be secured via screws to keep it in place  
when facing downward.  
The low frequency transducer shall have a polypropylene-coated cone  
and a butyl rubber surround which shall extend seamlessly over the  
edge of the speaker frame to protect against the elements. The high fre-  
quency transducer shall be constructed of polycarbonate, reinforced with  
a titanium film for additional weather resistance. The system shall with-  
stand Mil Spec 810 testing with specified durations for exposure to the  
following environments with no effect on its acoustical performance or  
structural integrity: salt spray (method 509.3), temperature (method 501.3  
and 502.3), humidity (method 507.3) and ultra-violet (method 505.3).  
The system shall have an IEC 529 splashproof rating of IP-X4.  
For theft deterrence, the installation access area shall be hidden  
behind a snap-out cover, and the access area shall be on the front of the  
loudspeaker for ease of installation and adjustment. The loudspeaker  
shall be rotatable over a minimum of 35° in all directions via a ball-  
type mounting system. The ball mechanism shall be internal to the cabi-  
net to allow low-profile mounting and better stability via short moment  
arm. The logo shall be rotatable for proper orientation when the loud-  
speaker is mounted horizontally or vertically.  
The external wiring connectors shall be screw-down terminals. Overall  
cabinet dimensions shall be no greater than 236 high x 186 wide x 159  
mm deep (9.3 x 7.4 x 6.3 in). and shall weigh no more than 4.0 kg (9  
lb). The finish shall be lightly textured black or white.  
The system shall be the JBL Model Control 25AV (or Control 25AV-  
TM  
WH) with included InvisiBall mounting system.  
 
®
Control 25AV  
Vertical 1/3 Octave Polars  
JBL Professional  
8500 Balboa Boulevard, P.O. Box 2200  
Northridge, California 91329 U.S.A.  
A Harman International Company  
SS Control 25AV  
CRP 15M  
11/01  
 

Insignia Car Stereo System CQ EH8160AK User Manual
Insignia Flat Panel Television NS 32L121A13 User Manual
Intel Stereo System sdk 85 system design kit User Manual
Intermec Label Maker PD41 User Manual
Iomega Computer Drive eGo Portable User Manual
JVC CD Player KD G341 User Manual
JVC Flat Panel Television 0706TKH MW VPC User Manual
KitchenAid Food Processor 4KFPM770 User Manual
KitchenAid Microwave Oven KEMS375 User Manual
Kramer Electronics Air Conditioner WP 211DS User Manual