JVC Flat Panel Television DT X71C User Manual

7" Portable On-camera LCD Monitor  
User Manual  
Model:  
HDSDI&HDMI, Waveform, Audio meter, Focus assist  
DT-X71F  
DT-X71H  
DT-X71C  
HDSDI&HDMI  
HDMI  
Please read this User Manual  
throughout before using.  
 
Maintenance  
Monitor  
1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to  
avoid short-circuit and damage.  
2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the  
monitor and do harm to human body, and it will cause the invalidation of product warranty.  
3. Please don't touch the screen with your fingers, which would probably deface the screen.  
4. Please don't press the screen; the LCD is extremely exquisite and flimsy.  
The power  
Please use the provided power adapter or the battery recommended by the manufacturer in order to avoid  
damage.  
Please never use the light connector (2-pin, female) in right front of camera handle to power the  
monitor; otherwise it will damage the circuit of the monitor.  
Please disconnect the power cable or take off the battery under the following situations:  
1. If you do not operate this monitor for a period of time;  
2. If the power cable or power adaptor is damaged;  
3. If you operate this monitor by the methods different from this User Manual, and cause unknown problems;  
4. If the monitor housing is broken.  
Working Environment  
1. Please don't lay this product on the unstable place.  
2. Please don't lay this product in hot, cold or wet location.  
Cleaning  
1. Please clean the screen with dry and downy cloth or special LCD cleanser.  
2. Please do not press hard when cleaning the screen.  
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the  
LCD.  
4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD  
protection film offered in the package.  
 
1. Features  
DT-X71F  
New high resolution 7LCD Panel  
16:9, 1024×600, 16.77 million colors, 900:1  
contrast, and H160°/ V160°viewing angle.  
Multiple inputs  
Peaking focus assist (red/blue switch)  
The Peaking focus assist function is to mark the  
sharpest edges of the image with red or blue color,  
for users to check if the subjects are focused.  
Zebra stripes  
2 HD/SD-SDI, 1 HDMI and 1 Composite input.  
Loop through outputs  
Zebra Stripes are used to check if the image is  
over exposed or not by showing black and white  
lines on the monitor. It is considered over exposed  
when luminance value exceeds 90%.  
Each of the 2 input HD/SD-SDI has loop through  
output.  
HDMI converted to SDI output  
Supported HDMI formats: 480i / 576i / 720p (50,  
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98  
24, 25, 29.97, 30), and the output SDI will embed  
the audio (48KHz) from HDMI.  
False color  
The false color is used to aid in the setting of  
camera exposure. Under false color mode, theres  
a false color key on the bottom of screen for  
reference. The over exposed subjects (above 101  
IRE) on the monitor will display as RED, and the  
underexposed subjects will display as BLUE. For  
correct exposed subjects, it will display as green  
and pink.  
Waveform (Y, Cb, Cr, R, G, B) and full scale  
There are totally 6 kinds of waveform display,  
available under both SDI and HDMI, to check the  
Luminance (Y), Blue-difference (Cb),  
Red-difference (Cr), Red (R), Green (G), Blue (B),  
and the Y, Cb, Cr can be simultaneously displayed, Blue Only  
R, G, B can be simultaneously displayed, and  
each of the waveforms can be set to full scale  
display.  
Under the Blue Only Mode, only the blue pixels  
are used to generate the image, because hue and  
saturation can be adjusted quicker and more  
accurately.  
Vector scope  
The displayed vector scope pattern is available  
under both SDI and HDMI, represents saturation  
as distance from the center of the circle, and hue  
as the angle, in standard position, around it.  
Histogram (R, G, B)  
DSLR scale zoom in  
The Canon DSLR outputs the CMOS sensor ratio  
HDMI and this zoom in mode can make the  
effective image scale full screen on the monitor.  
G-sensor auto flip  
The histogram is a bar graph that shows the  
distribution of luminance values in the picture.  
Therere R, G, B histograms that individually  
displayed simultaneously, available under both  
SDI and HDMI.  
Enable the G-sensor auto flip, the image will  
rotate automatically when monitor is bottom up.  
User definable function keys  
There are 3 function keys on the monitor front  
panel, and users could define the functions to the  
keys to achieve shortcut.  
16-ch audio meter  
Under HDSDI, it displays 16 channels audio bars,  
with mark, and under SDSDI or HDMI, it displays  
2 channels audio bars with mark. The audio bar is  
green, and will turn yellow when audio exceeds  
-20dB, and turn red when exceeds -10dB.  
SDI timecode  
User editable video title  
User can edit a video title for the current camera,  
and the title will display on the top of screen.  
Front and Rear 3-color TALLY light  
2 TALLY lights design, to give livesignals to  
people in front of the camera, as well as the  
Under SDI input, it can display the SMPTE  
timecode, which is used extensively for  
synchronization, and for logging and identifying  
material in recorded media.  
 
DT-X71H  
New high resolution 7LCD Panel  
16:9, 1024×600, 16.77 million colors, 900:1  
contrast, and H160°/ V160°viewing angle.  
Multiple inputs  
User definable function keys  
There are 2 function keys on the monitor front  
panel, that permit users to define shortcuts for the  
various functions.  
2 HD/SD-SDI, 1 HDMI, 1 Composite input  
and L/R stereo audio.  
User editable video title  
Loop through outputs  
User can edit a video title for the current camera,  
and the title will display on the top of screen.  
Front and Rear 3-color TALLY light  
2 TALLY lights design, to give livesignals to  
people in front of the camera, as well as the  
1 HD/SD-SDI loop through output.  
DSLR scale zoom in  
The Canon DSLR outputs the CMOS sensor ratio  
HDMI and this zoom in mode can make the  
effective image scale full screen on the monitor.  
Image Flip  
Set image to rotate by 180°.  
DT-X71C  
New high resolution 7LCD Panel  
16:9, 1024×600, 16.77 million colors, 900:1  
contrast, and H160°/ V160°viewing angle.  
Multiple inputs  
User definable function keys  
There are 2 function keys on the monitor front  
panel, and users could define the functions to the  
keys to achieve shortcut.  
1 HDMI, 1 Composite input  
and L/R stereo audio input.  
User editable video title  
Loop through outputs  
User can edit a video title for the current camera,  
and the title will display on the top of screen.  
Front and Rear 3-color TALLY light  
2 TALLY lights design, to give livesignals to  
people in front of the camera, as well as the  
1 Composite loop through output.  
DSLR scale zoom in  
The Canon DSLR outputs the CMOS sensor ratio  
HDMI and this zoom in mode can make the  
effective image scale full screen on the monitor.  
Image Flip  
Set image to rotate by 180°.  
2. Panel Instruction  
 
DT-X71F  
Front view  
PHONE: Earphone jack  
POWER: Power on/off  
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on  
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the  
POWER” again, the indicator is turned off and monitor is switched off.  
Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.  
IN: Input signal selection  
Press INand revolve the OKto select the input video signal.  
F1: User definable function key 1  
FOCUS: Peaking Focus Assist  
Press “FOCUSonce, it will display the current peaking on/off status. Press FOCUSagain to switch  
on RED line focus assist, switch on BLUE line focus assist, and switch off in turn.  
F.COLOR: False color  
Press “F.COLORonce, it will display the current false color on/off status. Press F.COLORagain to  
switch on/off the false color mode.  
DISPLAY: Display current settings  
Press “Display” to display safety mark, title and the current input signal information  
F2: User definable function key 2  
F3: User definable function key 3  
WAVEFORM: Display waveform  
Press “WAVEFORMonce, it will display the waveform menu as:  
Revolve OKto select a waveform display mode and turn it on.  
The selected waveform will display on the screen.  
VECTOR: Display vector scope  
Press “VECTORto switched on/off the Vector scope  
MENU: Press to enter Menu  
OK: Select and Apply  
Under menu system, revolve OKto adjust settings and press to apply; and out of menu system,  
directly revolve OKto adjust volume.  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
 
Rear view  
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
Battery mount:  
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.  
HDSDI IN1/2: HD/SD-SDI input (BNC connector)  
HDSDI OUT: HD/SD-SDI loop through output (BNC connector)  
HDSDI LOOP1/2: HD/SD-SDI loop through output (BNC connector)  
VIDEO IN: Composite video input (BNC connector)  
TALLY controlling port (RJ45)  
HDMI: HDMI input  
Input formats  
Input  
Supported formats  
CVBS  
PAL / NTSC  
480I / 576I / 480P / 576P  
1080i (60 / 59.94 / 50)  
720p (60 / 59.94 / 50)  
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)  
1080i (60 / 59.94 / 50)  
1080p (30 / 29.97 / 25 / 24 / 23.98)  
720p (60 / 59.94 / 50)  
480i (59.94)  
HDMI  
SDI  
SMPTE-274M  
SMPTE-296M  
SMPTE-125M  
ITU-R BT.656  
576i (50)  
 
DT-X71H  
Front view  
PHONE: Earphone jack  
POWER: Power on/off  
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and  
after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER”  
again, the indicator is turned off and monitor is switched off.  
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.  
VIDEO: Press to switch the input signal to Composite video  
HDMI: Press to switch the input signal to HDMI  
HD-SDI1: Press to switch the input signal to the first HD-SDI channel  
HD-SDI2: Press to switch the input signal to the second HD-SDI channel  
MENU: Press to enter Menu  
F1: User definable function key 1  
F2: User definable function key 2  
RATIO: 16:9 and 4:3 switch  
ZOOM: Picture Zoom-in  
Press ZOOMto switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.  
DISPLAY: Display current settings  
Press “Display” to display safety mark, title and the current input signal information  
OK: Select and Apply  
Under menu system, revolve OKto adjust settings and press to apply; and out of menu system,  
directly revolve OKto adjust volume.  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
 
Rear view  
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
Battery mount:  
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.  
HDSDI IN1/2: HD/SD-SDI input (BNC connector)  
HDSDI OUT: HD/SD-SDI loop through output (BNC connector)  
VIDEO IN: Composite video input (BNC connector)  
AUDIO L/R: Stereo audio L/R input (RCA connector)  
TALLY controlling port  
HDMI: HDMI input  
Input formats  
Input  
Supported formats  
CVBS  
PAL / NTSC  
480I / 576I / 480P / 576P  
1080i (60 / 59.94 / 50)  
720p (60 / 59.94 / 50)  
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)  
1080i (60 / 59.94 / 50)  
1080p (30 / 29.97 / 25 / 24 / 23.98)  
720p (60 / 59.94 / 50)  
480i (59.94)  
HDMI  
SDI  
SMPTE-274M  
SMPTE-296M  
SMPTE-125M  
ITU-R BT.656  
576i (50)  
 
DT-X71C  
Front view  
PHONE: Earphone jack  
POWER: Power on/off  
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on  
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the  
POWER” again, the indicator is turned off and monitor is switched off.  
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of  
time.  
VIDEO: Press to switch the input signal to Composite video  
HDMI: Press to switch the input signal to HDMI  
B/W: Black and White mode  
OVERSCAN: Overscan / Underscan switch  
MENU: Press to enter Menu  
F1: User definable function key 1  
F2: User definable function key 2  
RATIO: 16:9 and 4:3 switch  
ZOOM: Picture Zoom-in  
Press ZOOMto switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.  
DISPLAY: Display current settings  
Press “Display” to display safety mark, title and the current input signal information  
OK: Select and Apply  
Under menu system, revolve OKto adjust settings and press to apply; and out of menu system, directly  
revolve OKto adjust volume.  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
 
Rear view  
DC 12V IN: Connect with DC12V 4-pin XLR power adapter.  
Battery mount:  
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.  
VIDEO OUT: Composite video loop through output (BNC connector)  
AUDIO L/R: Stereo audio L/R input (RCA connector)  
VIDEO IN: Composite video input (BNC connector)  
HDMI: HDMI input  
TALLY controlling port  
TALLY Light: Red, Green and Yellow 3-color TALLY indicator  
Input formats  
Input  
Supported formats  
CVBS  
PAL / NTSC  
480I / 576I / 480P / 576P  
1080i (60 / 59.94 / 50)  
HDMI  
720p (60 / 59.94 / 50)  
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)  
 
3. Menu Operation  
Press “MENU” and it will display menu system  
Revolve OKto select an item. The selected item will be highlighted display.  
Press OKto enter the selected item.  
Under menu system, press MENUto back to previous menu.  
The menu will automatically save and quit if it remains idle.  
4. Picture Settings Submenu  
The Picture Settings Submenu includes:  
CONTRAST: 0-100 value adjustment  
BRIGHTNESS: 0-100 value adjustment  
HUE: 0-100 value adjustment  
(Only available under Composite input)  
SATURATION: 0-100 value adjustment  
SHARPNESS: 0-100 value adjustment  
PIC.MODE: User defined and preset picture  
modes: standard, soft and vivid selection  
5. System Configuration Submenu  
The System Configuration Submenu includes:  
RATIO: Select 16:9or 4:3to adjust the aspect ratio.  
SCAN: UNDERSCAN/ OVERSCANselection  
ZOOM: OFF, ZOOM1and ZOOM2selection  
ZOOM1: Canon DSLR scale zoom-in  
ZOOM2: Pixel to Pixel zoom-in  
MARKER: Select and set the safety mark  
scale from 80%, 85%, 90% and 95%.  
FLIP: Select YESto enable G-sensor auto  
flip.  
RESET: Revolve OKto RESET and press to  
recover all to factory setting.  
 
6. OSD Settings Submenu  
The OSD Settings Submenu includes:  
LANGUAGE: Menu language English / Chinese selection  
H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center.  
V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center.  
DURATION: Menu timeout setting  
Set a time (in seconds) in which the menu  
will automatically quit if remains idle.  
Default: 10 seconds; Range: 5 seconds to  
60 seconds.  
7. Title Settings Submenu  
Revolve "OK" button to select the letters, and press "OK" to input. Select SPACE to input space and DEL to  
delete the left letter. Max 10 letters are supported.  
After setting, press "MENU", the system will  
save data to current user and quit menu. The  
menu will automatically save and quit if it  
remains idle.  
8. Display Settings Submenu  
The DISPLAY settings submenu is to select the  
items to be displayed on screen when  
DISPLAYbutton is pressed. Revolve "OK" to  
turn on/off the items:  
(1) INFO: Including Input format, aspect ratio,  
underscan/overscan, zoom status  
(2) MARKER: Safety mark  
(3) TITLE: User edited title  
 
9. FUNCTION KEY Settings Submenu  
The F KEY Settings Submenu is to define  
Function Keys on the front keyboard.  
The DT-X71F has 3 function keys:  
F1, F2 and F3;  
The DT-X71H and DT-X71C has 2 function  
keys:  
F1 and F2.  
The available function items of each model are:  
-------------------DT-X71F-------------------  
01-RATIO: Aspect ratio switch  
-------------------DT-X71H-------------------  
01-RATIO: Aspect ratio switch  
02-SCAN: Underscan / Overscan switch  
03-ZOOM: Picture Zoom-in  
02-SCAN: Underscan / Overscan switch  
03-ZOOM: Picture Zoom-in  
04-PIC. MODE: Preset picture mode switch  
05-B/W: Color / Black & white switch  
04-CLR.TEMP: Color-temperature switch  
05-PIC MODE: Preset picture mode switch  
06-B/W: Color / Black & white switch  
07-REVERSE: Image flip  
06-BLUE ONLY: Blue only mode switch on/off  
07-ZEBRA: Zebra over exposure switch on/off  
08-VECTOR: Vector scope switch on/off  
09-PATTERN: Internal colorbar switch on/off  
10-RGB HIST: R, G, B Histogram switch on/off  
11-TIMECODE: SDI timecode display switch on/off  
12-F.COLOR: False color mode switch on/off  
13-AUDIO BAR: Audio meter display switch on/off  
14-FOCUS: Peaking focus assist switch on/off, and  
red/blue selection  
-------------------DT-X71C-------------------  
01-RATIO: Aspect ratio switch  
02-SCAN: Underscan / Overscan switch  
03-ZOOM: Picture Zoom-in  
04-CLR.TEMP: Color-temperature switch  
05-PIC MODE: Preset picture mode switch  
06-B/W: Color / Black & white switch  
07-REVERSE: Image flip  
10. TALLY Light Operation  
There are front and rear TALLY lights on the monitor, which can display RED, GREEN and YELLOW signals.  
The TALLY light controlling port is the RJ45 socket at the rear panel, and terminal description is as follows:  
Terminal  
1
2
3
4
5
6
7
8
Description  
Y
G
GND  
R
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.  
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.  
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting  
 
11. Specifications  
LCD Performance  
Size  
7.0 inches  
Resolution  
Aspect ratio  
Color system  
Brightness  
Contrast  
1024×RGB×600  
16:9/4:3  
NTSC/PAL  
400cd/m2  
900:1  
Color  
16.77 million colors  
H/V:160/160  
Viewing angle  
Video Format  
1080i (60 / 59.94 / 50)  
SMPTE-274M  
1080p (30 / 29.97 / 25 / 24 / 23.98)  
720p (60 / 59.94 / 50)  
SDI * SMPTE-296M  
SMPTE-125M  
480i (59.94)  
ITU-R BT.656  
576i (50)  
480I / 576I / 480P / 576P  
1080i (60 / 59.94 / 50)  
HDMI  
720p (60 / 59.94 / 50)  
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)  
General  
Working voltage  
DC12V, or Battery 6.5V-17V  
DT-X71F  
15W  
8W  
6W  
Power consumption  
DT-X71H  
DT-X71C  
Working temperature  
Working humidity  
Storage temperature  
Storage humidity  
Dimensions  
0℃~+40℃  
10%90%  
-15℃~+60℃  
10%90%  
192×139×47mm  
Net weight  
550g  
* DT-X71C doesnt support SDI input.  
12. Packing List  
1. Monitor  
×1  
×1  
×1  
×1  
×1  
×1  
×1  
2. User Manual  
3. Power adaptor  
4. Power cable  
5. Sun hood  
6. Screw ball head  
7. LCD protection film  
 
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC,  
and distributed in North America by JVC Professional Video Products.  
To obtain service or for further information, please contact:  
SWIT Electronics USA, LLC.  
Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129  
Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258·Fax: 408 228-8438  
 

InSinkErator Water Dispenser H Wave S User Manual
John Deere Weather Radio OMPFP12515 User Manual
JVC Camera Accessories AA V33U User Manual
JVC Car Stereo System KD AHD39 User Manual
JVC Projector KS RF150 User Manual
Kalorik Blender BL 24242 User Manual
Kawasaki Grinder 840329 User Manual
Kenmore Camper 1411686 User Manual
Kingwin MP3 Player KM 31BK User Manual
Koss DVD Player KS5429 2 User Manual