Jabra Projector Accessories SP CEIL 006 User Manual

·
·
To avoid personal injury, use only an approved projector mount. Using  
an unauthorized projector mount may lead to poor ventilation and  
projector failure.  
Hardware Description  
The Digital Projector Mount utilizes the following hardware. Note that the  
letters associated with the hardware on this list correspond to the letters  
listed in the instructions for each installation method.  
When installing the projector mount, keep in mind that the projectors  
focus ring is not squarely in the center of the front of the projector, but  
offset by several inches. Make sure that when you mount the projector  
you offset the installation to match the amount of inches that the  
projectors focus ring is offset from the center of the front of the  
projector.  
27700B S.W. Parkway Ave.  
Wilsonville, Oregon 97070-9215  
1-800-294-6400  
(A) Three (3) 4 (mm) x 16 (mm) Phillips head screws  
SP-CEIL-006 DIGITAL PROJECTOR MOUNT  
Getting the Digital Projector Ready  
(B) One (1) mounting bracket  
Before you start the installation process, prepare your Digital Projector by  
performing the following steps  
InstallationInstructions  
These are the installation instructions for your Digital Projector Mount.  
Included are four methods of installation. Select the method that works  
best for your viewing situation. The methods are:  
(FIGURE 1).  
1. Turn the projector (C) upside down and place it on a clean flat  
surface, preferably on a towel.  
Fixed Height Ceiling Installationbest for short ceilings, eight (8) or  
2. Locate the mounting bracket (B) and align it over the holes on the  
lower  
projector.  
3. Locate the three (3) 4 (mm) x 16 (mm) Phillips head screws (A).  
Adjustable Height Ceiling Installationbest for high ceilings, nine (9)  
feet or higher *  
4. Use the Phillips head screwdriver to secure the mounting bracket  
(B) to the projector via the three (3) Phillips head screws (A). Do  
not over-tighten the screws.  
(C) Digital Projector (not included  
(D) Ceiling structure (not included)  
Wall Mount Installationfor installing the Digital Projector Mount on a  
rear wall  
Figure 1  
A
Tabletop, Shelf, or Floor Installationfor installing the Digital  
Projector Mount on a tabletop, shelf, or floor  
(E) One (1) upper plate  
B
C
*If the required height range is greater than 12½", the optional SP-LTMT-  
EXTP could be used to extend the length of the suspension adapter (see  
(N) under Hardware Description” on the next page). For further  
information or ordering assistance, please contact us at the phone  
number and address listed at the top of this column.  
(F) Four (4) commercially available hardware anchors for the installation  
environment (not included)**  
Before You Start the Installation  
The wall, ceiling, tabletop, shelf, or floor where you want to install the  
digital projector must be capable of supporting a weight that is five (5)  
times the weight of the projector you are installing. Consult the projectors  
documentation for weight specifications. If the wall, ceiling, tabletop, shelf,  
or floor is not strong enough to handle five (5) times the weight of the  
projector, then you must reinforce the installation environment. If you are  
unsure about the installation environment, please consider having it  
reinforced and having the projector installed by qualified personnel.  
Failure to do so could result in serious personal injury and damage to the  
projector.  
(G) One (1) swivel bracket (unit-attached)  
Tools Needed for Installing the Digital Projector Mount  
You need the following tools to install the Digital Projector Mount:  
·
·
·
Phillips head screwdriver (not included)  
Allen wrench (included)  
Drill (for installation environment only - do not use a drill on the Digital  
Projector or the Digital Projector Mount) and drill bit to match the  
hardware for your installation environment (not included)  
·
The commercially available hardware (F) that is required by your  
installation environment (not included)  
Projected Image Sizes  
For image sizes based upon the projectors distance to the screen,  
consult the Projected Image Size” section in your projectors Users  
Copyright ã by InFocus Corporation  
Wil
s
o
n
vill
e
,
O
R.
A
ll rights reserved  
Guide.  
 
FIGURE 3  
FIGURE 4  
Wall Mount Installation  
Complete the following steps to install the projector mount and projector  
to your wall. (FIGURE 4)  
Note: Look at the bottom of the swivel bracket (G) and locate the arrow.  
Make sure you install the projector mount with the arrow pointing toward  
your screen.  
15. Use the Allen wrench to remove the upper plate (E) from the swivel  
bracket (G).  
16. Use the Allen wrench to remove the two screws from the enclosed  
end of the of the suspension adapter (N), and place it (N) into the  
slotted extension on the upper plate (E). Make sure that the two (2)  
outer holes on the suspension adapter (N) align with the holes on  
the slotted extension on the upper plate (E).  
17. Screw the two screws removed in step 2 into the two (2) holes to  
secure the suspension adapter (N) to the upper plate (E).  
18. Attach the swivel bracket (G) to the suspension adapter (N) and  
secure them with two screws removed in step 1.  
19. Secure the upper plate (E) to the wall (M) using the commercially  
available hardware (F) suitable for your environment. Be sure that  
the swivel bracket (G) arrow is pointing toward your screen.  
20. Carefully raise the projector (C) with the mounting bracket (B)  
attached and insert it into the bottom of the swivel bracket (G) by its  
tabs.  
21. Rotate the projector (C) with the mounting bracket (B) attached  
180º so that the projectors focus rings is pointing toward your  
screen.  
22. Align the safety screw (H) on the swivel bracket (G) with the end of  
the arrow -shaped slot on the mounting bracket (B) and screw it  
through the opening to prevent further rotation. Hand-tighten the  
screw (H).  
23. Hand-tighten the remaining two clamp screws (J) to secure the  
mounting bracket (B) to the swivel bracket (G).  
Check all of the hardware for proper tightness and security. Do not over-  
tighten the screws.  
 
Figure 5  
Tabletop, Shelf, or Floor Installation  
Complete the following steps to install the projector mount and projector  
on a tabletop, shelf, or floor (FIGURE 5).  
Note: Look at the bottom of the swivel bracket (G) and locate the arrow.  
Make sure you install the projector mount with the arrow pointing toward  
your screen.  
24. Use the Allen wrench to remove the upper plate (E) from the swivel  
bracket (G).  
25. Use the Allen wrench to remove the two screws from the enclosed  
end of the of the suspension adapter (N), and place it (N) into the  
slotted extension on the upper plate (E). Make sure that the two (2)  
outer holes on the suspension adapter (N) align with the holes on  
the slotted exet nsion on the upper plate (E).  
26. Screw the two screws removed in step 2 into the two (2) holes to  
secure the suspension adapter (N) to the upper plate (E).  
27. Attach the swivel bracket (G) to the suspension adapter (N) and  
secure them with two screws removed instep 1.  
28. Secure the upper plate (E) to the tabletop, shelf, or floor (M) using  
the commercially available hardware (F) suitable for your  
environment. Be sure that the swivel bracket (G) arrow is pointing  
toward your screen.  
29. Carefully lower the projector (C) with the mounting bracket (B)  
attached and insert it into the bottom of the swivel bracket (G) by its  
tabs.  
30. Rotate the projector (C) with the mounting bracket (B) attached  
180º so that the projectors focus ring is pointing toward your  
screen.  
31. Align the safety screw (H) on the swivel bracket (G) with the end of  
the arrow -shaped slot on the mounting bracket (B) and screw it  
through the opening to prevent further rotation. Hand-tighten the  
screw (H).  
32. Hand-tighten the remaining two clamp screws (J) to secure the  
mounting bracket (B) to the swivel bracket (G).  
Check all of the hardware for proper tightness and security. Do not over-  
tighten the screws.  
Figure 5  
 

Indesit Washer IWCN 61051X9 User Manual
Intel Handheld Game System SIM4 02 User Manual
Invacare Mobility Aid Powered Wheelchair User Manual
IOGear Network Cables GHPU01 User Manual
JVC CRT Television 50050690 User Manual
JVC Stepper Machine CS V6934 User Manual
JVC Stereo System CA EXD5 User Manual
Kalorik Food Processor USK MCH 33526 User Manual
Klipsch Speaker ksw 08 new User Manual
Kompernass DVD Player KH 6507 User Manual