Jensen Remote Starter JKRS3 User Manual

Model JKRS3  
Installation Manual  
3 Channel Remote Start / Keyless Entry System  
Installation Instructions  
This Unit Is Intended For Installation In Vehicles With  
12 Volt Negative Ground Electrical Systems,  
Gasoline or Diesel With True Tach Reference  
And Automatic Transmissions Only.  
Kit Contents  
(1) Control Module  
(1) 3 Button High Frequency Transmitters  
(1) 5 Button Two Way LED Based Transceiver  
(1) On Glass Mount Superheterodyne Transceiver  
(1) Multi Pin Input/Output Harness  
(1) Six Pin Power Harness  
(1) Diesel Wait To Start Input  
(1) Auxiliary 4 Pin Output Harness  
(1) 2 Pin Door Lock Harness  
(2) 30 Amp In-line Fuse Holders With Fuses  
(1) Control Switch  
(1) Plug In Push-Button Programming Switch  
(1) Ring Terminal  
(4) 1/2" Long Screws  
(1) Pin Switch  
(1) Remote Start Warning Label  
(1) Literature Package  
128-7052  
1 of 16  
 
THE TRANSCEIVER/ANTENNA ASSEMBLY:  
The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash-  
board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best  
reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic  
shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear  
window location for best reception. Secure the antenna with double stick tape provided. After securing the antenna  
with tape, we advise also securing a section of the antenna cable to a fixed support. This will prevent the antenna  
from dropping down in case the double stick tape is exposed to extreme heat, which may loosen its gummed  
surface. Route the 4 pin connector toward the control module using caution not to pinch the cable as this will cause  
poor or no RF reception to the control module.  
I M P O R TA N T !  
DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THE  
CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR  
TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BAT-  
TERY PRIOR TO MAKING ANY CONNECTIONS.  
WIRING THE 6 PIN MAIN POWER HARNESS:  
RED w/ WHITE TRACE WIRE: + 12 volt Battery 1 Source  
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder  
provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.  
RED WIRE: + 12 Volt Battery 2 Source  
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder  
provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles have more than one battery  
source supplying power to the ignition switch. Separate feed wires must be used for the Red and Red/White wires. If  
your vehicle does not have two battery feed wires at the ignition switch then it is possible to connect both wires to the  
vehicle's battery. This wire provides power for the start relay and the accessory relay.  
I M P O R TA N T !  
IT IS THE RESPONSIBILITY OF THE INSTALLING TECHNICIAN TO DETERMINE THE LOAD FACTOR OF THE  
VEHICLES ELECTRICAL CIRCUITS WHEN THE VEHICLE IS RUNNING AND TO ADEQUATELY FUSE THE TWO  
POWER WIRES BASED ON THAT LOAD. IF THE VEHICLE, RUNNING UNDER LOAD WITH THE AIR CONDITIONER,  
HEATER BLOWER MOTOR, AND ACCESSORIES EXCEEDS 24 AMPS CONTINUOUS, WE RECOMMEND THAT  
TWO FUSES BE USED IN COMBINATION ON EACH POWER WIRE AS SHOWN BELOW. FOR ADDITIONAL INFORMA-  
TION SEE TECH UPDATE ISSUED 9/30/96.  
YELLOW WIRE: Starter Output  
Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in  
gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you  
to properly identify the circuit and select the correct installation method. In addition you will realize why the  
connection of the safety wire is required for all mechanical switch configurations.  
Failure to make this connection properly can result in personal injury and property damage. In all installations it is the  
responsibility of the installing technician to test the remote start unit and assure that the vehicle cannot start via RF  
control in any gear selection other than park or neutral.  
In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will be made  
to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when the ignition  
switch is turned to the start (crank) position only. This wire will have 0 volts in all other ignition switch positions.  
NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral  
switch configuration, this connection must be made between the starter inhibit relay, (when used) and the  
neutral safety switch as shown in the following diagram.  
3
128-7052  
3 of 16  
 
Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and  
property damage.  
SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.  
BLUE WIRE: Ignition 1 Output  
Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key  
is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions and will have 0 volts when the key is turned  
to the "OFF" and "ACCESSORY" positions.  
For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the vehicle  
requires glow plug pre-heating.  
GREEN WIRE: Ignition 2 Output  
Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition key  
is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position. This wire will show 0  
volts when the key is turned to the "OFF" and "ACCESSORY" positions.  
NOTE: See programming information concerning this wire to allow output during the "START" mode.  
VIOLET WIRE: Accessory Output  
Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition  
switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to  
the "OFF" and "START" or "CRANK" positions.  
4
128-7052  
4 of 16  
 
WIRING CONNECTIONS: 12 Pin Input / Output Harness  
Black Wire: Chassis Ground Source  
Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to  
remove any paint or grease and secure this wire with a self-tapping screw and ring terminal.  
BLACK w/WHITE TRACER WIRE: Control Switch  
The Black w/ White tracer wire provides ON-OFF control of the Remote Starter.  
When the Black w/ White wire is switched to a full time ground, the APS-55 Remote Start Module is operative. When  
the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled.  
ConnecttheBlackw/Whitetracerwiretooneofthewiresfromthebackofthepreviouslymountedcontrolswitch. Connect  
the remaining wire of the control switch to chassis ground. Always try to mount the switch so that the ON position is  
in an upward or toward the driver direction.  
GRAYWIRE:NegativeInhibitInput1  
Connect the GRAY wire to the previously mounted hood pin switch provided. This wire will be routed through the firewall  
into the engine compartment. It is necessary to use an existing grommet when passing wires through the firewall to  
prevent short circuiting. This is an important safety feature of the System, failure to use this feature can result in serious  
injury. Route the wire to the pin switch and connect it using the bullet connector provided.  
GRAYw/BLACKTRACERWIRE:NegativeInhibitInput2  
Any time the gray w/ black tracer wire is grounded, the Remote Starter will stop operating, even if the signal is received  
from the transmitter.  
If the brake light switch in the vehicle switches ground to the brake light circuit, connect the Gray w/ Black trace wire  
to the output of the brake light switch. If the brake light switch in the vehicle switches +12 Volts, do not use the Gray  
w/ Black wire; see Brown w/ Black tracer wire.  
BROWNWIRE: Positive Inhibit Input 1  
Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is received  
from the transmitter.  
If the vehicle has a factory installed hood pin switch and that switch provides + 12 Volts to an under hood light, the Brown  
wire can be connected to the existing pin switch.  
BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2  
Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal  
is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect  
theBrownw/Blacktracewiretotheoutputofthebrakelightswitch. Ifthebrakelightswitchinthevehicleswitchesground,  
do not use the Brown w/ Black wire; see Gray w/ Black tracer wire.  
5
128-7052  
5 of 16  
 
Brake Switch Positive Shutdown Detail  
YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output  
NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to  
in the vehicle.  
This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Volts when the ignition  
key is “OFF” and when the vehicle is running under the control of the remote starter.  
This wire should be connected to the ignition input of the alarm system.  
The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/  
unlock the doors while running under control of the remote start unit.  
(2) WHITE Wires: Parking Light Flasher  
These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking lamp relay.  
If the vehicle's parking lights are a +12 volt switched system, connect (1) of the White wires to a fused (15A max.) +12  
volt battery source, and connect the second White wire to the vehicle's parking light wire.  
If the vehicle's parking lights are a chassis ground switched system, connect (1) of the White wires to a chassis ground  
source, and connect the second White wire to the vehicle's parking light wire.  
Switch  
LIGHT BLUE Wire: Ignition 3 / Shock Disable Output  
This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,  
and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the  
applications described below, a relay will be required. The Light Blue wire can be used to accommodate the following  
situations:  
6
128-7052  
6 of 16  
 
A. Shock Sensor By Pass:  
If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation  
period, then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Light Blue  
Wire to terminal #86 of a external relay. Connect terminal #85 of the relay to a fused + 12 volt battery source. Cut  
the shock sensor trigger wire and connect one end of the cut wire to terminal #30 and the other end of the cut wire  
to terminal #87a. Just before the Remote Start unit is activated, the relay contacts will open, preventing the shock  
sensor's operation until the Remote Start unit shuts off.  
B. Ignition 3 Output:  
Some newer vehicles use a third ignition wire, which is required to start and keep the vehicle's engine running. If  
this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect terminal #30 & #85 to a  
fused + 12 volt battery source rated for a minimum of 25 Amp. Connect terminal #87 to the third ignition wire in the  
vehicle.  
C. GM VATS Key Override:  
If the vehicle has the General Motors VATS system installed, you will need to bypass the system while the vehicle  
is operating under the control of the Remote Start Unit. To Do This;  
1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the key's value  
from the resistor pack supplied.  
2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the ignition switch to  
the VATS control module.  
NOTE: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later model  
Cadillacs, they are run through an orange sleeve, and are either both Black, both Yellow, or both  
White wires. Consult the factory service manual for additional information.  
3. Connect the Light Blue Wire from the Remote Start Unit to terminal #86 of an external relay. Connect terminal #85  
of the relay to a fused + 12 volt battery source.  
4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay. Connect  
the other side of the (#1) wire to terminal #30.  
5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown).  
NOTE:  
The above information and following diagram is for the GM VATS system only. For GM PASS LOCK  
System you will require the Audiovox AS-PASS II Module.  
General Motors VATS By-Pass Diagram  
7
128-7052  
7 of 16  
 
Green/Orange Wire: Tach Sensor Input  
This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This  
wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to  
the negative side of the ignition coil. This Remote Start unit learns the tach rate of the vehicle and in most cases will  
operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a single coil unit for  
each cylinder, it may be necessary to connect this wire to more than one cylinder for proper tach reference. See multi  
coil wiring detail shown later in this manual for additional information.  
Tachometer Input Wiring Detail  
Green/Yellow Wire: Diesel Wait To Start Input  
The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this  
wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by the remote  
start unit, the glow plug circuit gets energized, (+ 12 volts), when the glow plug circuit of the vehicle drops the + 12 volts,  
which effectively grounds the wait to start input, then 500mS later the starter will engage. This wire can also be connected  
to the Glow Plug Bulb wire in the vehicle if this bulb wire gets + 12 volts when the ignition comes on and drops low when  
the glow plug circuits temperature is reached. Be sure to fuse the wire with a 1 Amp Fuse when connecting to a high  
current circuit such as a factory glow plug wire. The fuse should be installed as close to the high current wire as possible.  
If you are installing this unit in a Gasoline vehicle, this wire is not used.  
WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS  
The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during  
different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they  
occur will allow you to determine if they are needed for the particular vehicle you are working on as well as how  
to use them.  
Black w Blue Trace Wire: Pulsed Ground Output Before Start  
The Black w/ Blue Trace wire will provide a 1 second 300 mA pulsed ground output 1.5 second before the  
remote start unit activates as well as when the transmitter is used to disarm the system. Typical use for this  
output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when  
the remote start unit engages or when the transmitter is used to unlock the doors.  
Black w/ Light Green Trace Wire: Pulsed Ground Output After Start  
The Black w/ Light Green Trace wire will provide a 1 second 300ma pulsed ground output after the vehicle is  
started under control of the remote start unit. Typically this wire will be used to re-lock the vehicle doors if the  
doors unlock automatically when the factory anti-theft system is disarmed.  
Black w/ Red Trace Wire: Pulsed Ground Output After Shutdown  
The Black w/ Red Trace wire will provide a 1 second 300 mA pulsed ground output after the remote start unit  
shuts down. This output will occur regardless of whether the circuit times out or is manually terminated.  
Typically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the ignition  
circuit transitions to off.  
Black w/ Yellow Trace Wire: Ground Output During Start (Crank)  
The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote start  
unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM vehicles.  
This wire is also referred to as the ECM wake up wire in some Chrysler vehicles.  
8
128-7052  
8 of 16  
 
NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is  
more than 300 mA.  
2 Pin Door Lock/Unlock Harness: (White Connector)  
The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the  
vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability of 300mA. Many  
vehicles today have factory door lock relays which can be connected directly to these outputs, however always confirm  
that the factory relays in your particular vehicle do not exceed the rated 300mA output of the units door lock/unlock  
circuit. Plug the 2 pin connector of the door lock/unlock harness into the mating connector shell of the control module.  
Determine the door lock circuit of the vehicle you are working on and wire according to the diagrams shown.  
3 Wire Ground Switched Door Lock Circuits:  
In this application, the Red wire of the 2 pin harness provides a ground pulse during the arming sequence, or pulsed  
ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the  
factory door lock relay.  
The Green wire of the 2 pin harness provides a ground pulse during the disarming sequence, or pulsed ground  
unlock output. Connect the Green wire to the low current ground signal wire from the factory door unlock switch to the  
factory door unlock relay. See Below For Wiring Detail.  
3 Wire Ground Switched Door Lock/Unlock Wiring Detail  
3 Wire Positive Switched Door Locks:  
In this application, the Red wire of the two pin harness provides a + 12 volt pulse during the disarming sequence, or  
pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock  
switch to the factory door unlock relay.  
The Green wire of the two pin harness provides a + 12 volt pulse during the arming sequence or pulsed 12 volt lock  
output. Connect the Green wire to the low current 12 volt signal wire from the factory door lock switch to the factory  
door lock relay. See Below For Wiring Detail.  
3 Wire Positive Switched Door Lock/Unlock Wiring Detail  
9
128-7052  
9 of 16  
 
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt  
Door Lock Control Circuits  
These applications require the use of additional components which may include relays, fixed resistors, or for  
convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the  
Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits.  
2 Pin Blue Connector : Programming Switch  
Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the control  
module and plug it into the mating blue connector on the side of the module.  
4 Pin Antenna/Receiver Connector: (White Connector)  
Plug the previously routed three pin connector from the antenna transceiver assemble into the mating connec-  
tor of the control module. This connector supplies 12 volts, ground and RF data from the antenna transceiver  
to the remote start module. Be certain this connector is firmly seated making good contact to the control unit.  
1. RF Programmable Features:  
Feature Selection  
1 Run Time  
2 Ign. 2 During Crank  
1 Flash  
5 Min.  
Off  
2 Flash  
10 Min.  
On  
3 Flash  
15 Min.  
4 Flash  
20 Min.  
Default  
10 Min.  
On  
3 Light Output During Run Steady  
Flash  
Tach  
NA  
On  
3.5 Sec/3.5 Sec  
1.0 Sec  
Diesel 10  
Steady  
Tach  
NA  
4 Tach Mode  
NA  
5 Voltage Level  
6 Trouble Shooting  
7 Door Locks  
8 Crank Time  
9 Gas/Diesel  
NA  
Off  
1 Sec/1 Sec  
0.8Sec  
Gas  
Off  
1 Sec/Dbl 1 Sec  
1.5 Sec  
Diesel 15  
1 Sec/1 Sec  
1.0  
Gas  
2.0 Sec  
Diesel 20  
To program these selectable features:  
a.Turn the ignition key to the ON position.  
b.Press and release the program switch 3 times.  
c. Immediately turn the ignition key OFF, then back to ON.  
d.Press and release the program switch 2 times  
e. Use the Start button on the transmitter to advance to the feature that you want to change. EXAMPLE - If you need  
to change programmable feature number 3, press and release the start button on the transmitter 3 times in  
succession. The parking lights will flash 3 times confirming that selected feature 3 can now be programmed.  
f. Use Lock button on the transmitter to change the selection of the programmable feature. If you are not sure what  
the setting for any feature is, press the lock button 1 one time, the parking lights will flash once or twice indicating  
the features setting.  
NOTE: Once you enter the feature-programming mode, do not allow more that 15 seconds to pass between  
steps, or the programming will be terminated.  
NOTE: IftheGlowPlugsensewire,Green/Yellowisconnected,thiswirewillhavepriorityoverthesettingoffeature  
#9.  
2. Programming Tach Rate:  
NOTE: All applications require that tach be programmed.  
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start without  
first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored.  
If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running  
in certain instances and could re-engage the starter motor.  
The Remote Car Starter will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and or single  
injector. To learn tach;  
a. Turn the ignition key to the ON position.  
b. Press and release the program switch 3 times.  
10  
128-7052  
10 of 16  
 
c. Immediately turn the ignition key OFF.  
d. Hold the program switch ON, then start the vehicle using the ignition key.  
e. When the unit senses the tach signal, the parking lights will begin to flash.  
6. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored  
and the unit is now out of the program mode.  
3.Diagnostics:  
a. Be sure that programmable feature number #6 is set to the "Diagnostics On" mode.  
b. Press and hold the program switch on, then turn the ignition key to the "ON" position.  
c. The lights will flash and the number of flashes will indicate the reason for shutdown on the last remote start attempt.  
The indications are as follows.  
1Flash  
5, 10, 15, or 20, minute run timer expired.  
2 Flashes Low or No tach signal received.  
3 Flashes Positive or Negative input shut down.  
4 Flashes Control switch was moved to "Off" position.  
5 Flashes RF Shutdown command received.  
6 Flashes High RPM signal over speed shut down.  
7 Flashes Tach has NOT learned.  
Multi Coil Pack Adapter: (Optional)  
The multi coil pack adapter, (P/N 136B1400), is designed for use with vehicles that do not respond to single coil tach  
programming. Although the tach resolution of this circuit is designed to interface direct with most vehicles, there may  
be an occasion where the following circuit may be required.  
To use the adapter, the Green/Black wires must connect to the negative side of the ignition coil(s).  
1. For vehicles utilizing independent coils per cylinder, connect the three Green/Black leads to alternate coils. To  
achieve optimum performance the coil signals must be evenly distributed. This is accomplished by first  
mapping out the firing order of the engine in groups of as indicated below. Draw a circle around any of the  
columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylinder  
number which appears in any of the circles.  
2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8  
cylinder, four coil systems, connect to any of the three coils.  
3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on  
and start position and have 0 volts with the ignition in the off position.  
4. Connect the Green wire to the tach input of the Audiovox remote start unit.  
TESTING YOUR INSTALLATION:  
W A R N I N G ! The following procedure must be performed after the installation of an Audiovox Remote Start  
Device. It is the responsibility of the installing technician to complete these tests. Failure to test the  
unit in the following manner may result in personal injury, property damage, or both.  
HOOD PIN SAFETY SHUT DOWN:  
The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while a  
mechanic or vehicle owner is performing normal routine vehicle maintenance.  
To test the integrity of this circuit:  
1. With the driver's window in the down position, start the vehicle using the RF transmitter.  
2. Reach inside the car and pull the hood release.  
11  
128-7052  
11 of 16  
 
3. Raise the hood and confirm that the remote start unit shuts down.  
If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit.  
WA R N I N G ! !  
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE  
OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE.  
MANUAL SHUT DOWN / ENABLE CIRCUIT:  
The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the Remote  
Start Unit regardless of the RF transmitter operation.  
To test the integrity of the manual shut down / enable circuit:  
1. Place the control switch in the on (Closed To Ground) position.  
2. Start the vehicle using the RF transmitter.  
3. The vehicle should start and run under the control of the remote start unit.  
4. Move the switch to the off (Open From Ground) position, the vehicle should shut off.  
If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire of the Audiovox  
Remote Start Unit. If you have a plug in enable switch, check that the 2 pin connector is firmly seated in the mating  
connector on the control module.  
WA R N I N G ! !  
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE  
OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE.  
NEUTRAL START SAFETY TEST:  
The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any position  
other than Park, or Neutral. When installing a Remote Start Device, it is imperative that the Yellow Starter wire be  
connected to the ignition switch side of the Neutral Start Switch. Consideration for the placement of a starter inhibit  
relay is important as well, and should be connected to the ignition switch side of the Yellow Start Wire.  
To test the integrity of the Neutral Start Safety Circuit:  
1. Set the vehicle parking brake.  
2. Block the drive wheels to prevent vehicle movement.  
3. Temporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch.  
4. Sitting in the vehicle, start the engine using the vehicle's ignition key.  
5. Step on the brake pedal and shift the gear selector into reverse.  
6. Allow the transmission to shift. When you feel the engine pull, do not move the gear selector just turn the ignition  
switch off. DO NOT attempt to remove the key.  
7.Keeping the brake pedal depressed, activate the RF transmitter in an attempt to start the vehicle. The car should  
not start.  
8. Repeat the above test this time move the gear selector to the drive position. If the unit attempts to start, failing this  
test, recheck your Yellow Wire's connection. This wire must be connected to the ignition switch side of the Neutral  
Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, it will be  
necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. The information concerning the  
Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has  
this type of safety switch and will provide alternate wiring methods to accommodate this situation.  
WA R N I N G ! !  
REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY  
DISCONNECTED IN STEP 3.  
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF  
THE NEUTRAL SAFETY START FEATURE.  
12  
128-7052  
12 of 16  
 
MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:  
Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a  
remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral,  
the mechanical function will not allow the key to be turned to the start position or be removed from the ignition cylinder. This  
configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for electrical operation.  
Because of this potential problem, this installation requires the additional connection of a safety wire from the remote start device to  
the vehicle Park/Neutral ECM Input or the vehicle key in sensor. This connection will prevent remote start operation if the key is left  
in the ignition switch regardless of the gear selector position.  
PARK / NEUTRAL ECM INPUT:  
The Park / Neutral ECM input is the preferred method of installation. This not only maintains the integrity of the factory circuit, it is also  
the easiest to install, providing the vehicle you are working on has this ECM input.  
The installation required for this application (shown below), indicates the slight reconfiguration of the control switch wiring and the  
addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM input circuit. To connect the Audiovox remote start unit to  
the GM Park / Neutral ECM input:  
1. Locate the Orange / Black reference wire in the "C2" connector found at the ECM in GM B Body vehicles or, locate the  
equivalent reference wire in the vehicle you are installing the Audiovox Remote Start Unit in.  
2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire.  
3. Connect the Anode, (Non Striped) end, of the diode to one side of the Remote Start enable switch.  
4. Connect the other side of the enable switch to the Black/White enable input wire of the Remote Start unit.  
The reference diagram below shows a typical GM B Body ECM reference wire and how it is to be connected to the Remote Start  
Unit.  
KEY IN SENSOR CIRCUITS:  
If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives  
available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will  
prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.  
AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following two  
circuits may be used only if the above circuit is not available.  
NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the  
ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down. This  
must be explained to the operator as it is in contrast to the normal operation of a vehicle utilizing an electrical  
neutral start switch and is inconsistent with the operator's manual.  
Additional information concerning Key In Sensor methods 1 & 2 are listed below and should be reviewed before  
considering either alternative.  
Method 1 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear  
other than Park or Neutral while the key is in the ignition cylinder. However, if the key is left in the ignition switch and  
the door is left opened, the added relay will be energized causing a 150mA drain on the battery.  
Method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear  
other than Park or Neutral while the key is in the ignition cylinder. However, the original factory key in chime module will  
not alert the owner that the key has been left in the ignition switch. In addition, this may also effect other warning tones  
13  
128-7052  
13 of 16  
 
such as the light on reminder.  
These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the  
consumer.  
Circuits may be used only if the above circuit is not available.  
To connect to the key in sensor as shown in method 1:  
1.Locate the control wire that connects the drivers door pin switch to the key in sensor switch.  
2.Cut this wire and connect the ignition cylinder side to chassis ground.  
3.Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .  
4.Cut this wire and connect the ignition cylinder side to terminal #30 of a P&B VF45F11 or equivalent relay.  
5.Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side  
to the negative shut down safety wire (Gray / Black) of the Remote Start Unit.  
6.Connect terminal #86 of the relay to a fused +12 volt constant battery source.  
7.Connect terminal #87 of the relay to the Chime Module side of the previously cut wire in step 4.  
8.Connect terminal #85 of the relay to the Drivers Door side of the pin switch wire previously cut in step 2.  
METHOD 1  
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this  
is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be  
connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the  
hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual diode  
assembly packaged with the Remote Start Unit as shown below.  
METHOD 2  
To connect to the key in sensor circuit as shown for method 2:  
1. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.  
2. Cut this wire and connect the ignition cylinder side to chassis ground.  
3. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .  
4. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire Gray/  
Black, using a 4002 series diode as shown above.  
14  
128-7052  
14 of 16  
 
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If  
this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be  
connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to  
the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual  
diode assembly packaged with the Audiovox Remote Start Unit as shown in this installation guide.  
AFTER THE CONNECTION OF THE NEUTRAL START SAFETY WIRE AS INDICATED IN ANY OF THE PREVIOUS  
ALTERNATE CONFIGURATIONS, THIS CIRCUIT MUST BE TESTED FOR OPERATION.  
Retest by following the steps outlined in the NEUTRAL START SAFETY TEST shown in this manual.  
COMPLETING THE INSTALLATION:  
After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the  
system:  
1.If you have not done so already, place the red rubber handle cover over the handle of the control switch for ease  
of identification. This will allow your customer to distinguish the Remote Start control switch from the program  
switch.  
2. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that  
the chosen mounting location will not inhibit any of the controls of the vehicle.  
3.Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with  
under the dash board or in the engine compartment areas.  
CAUTION: Particularly avoid the area around the steering shaft and column, as wires can wrap around  
these mechanisms and impair the safe operation of the vehicle.  
4.Apply the Caution Labels supplied with this kit to a conspicuous area in the engine compartment. Make sure  
to clean the surface before affixing the label.  
5.Check the vehicle's wipers, lights, horn, etc.... to insure proper operation.  
6.Replace all panels that were removed during installation, and retest the system.  
7.Explain all activated features and safety systems associated with Remote Start Unit installed to the customer.  
8.Place the Valet Switch Tag and or the Remote Start Control Switch Tag on their respective switches and  
point these out to the customer.  
15  
128-7052  
15 of 16  
 
© 2004 Audiovox Electronics Corp., Hauppauge, NY 11788  
128-7052  
128-7052  
16 of 16  
 

John Deere Brush Cutter CX15 User Manual
John Deere Lawn Mower X700 User Manual
John Deere Network Cables PFP11260 User Manual
Johnson Controls Refrigerator S1 TCZSD01A User Manual
Jura Capresso Coffeemaker IMPRESSA C5 User Manual
Kaidan Camcorder Accessories V14 User Manual
Kenwood Stereo Amplifier 374 User Manual
Kidco Safety Gate G60c User Manual
KitchenAid Ice Maker KUIS18PNJB4 User Manual
Korg Electronic Keyboard 6voc User Manual