Jensen Turntable SB6051 User Manual

 
7. DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE  
MANUFACTURER’S INSTRUCTIONS.  
8. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS,  
STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.  
9. DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED OR GROUNDING – TYPE PLUG. A  
POLARIZED PLUG HAS TWO BLADES WITH ONE WIDER THAN THE OTHER. A GROUNDING  
TYPE PLUG HAS TWO BLADES AND A THIRD GROUNDING PRONG. THE WIDE BLADE OR THE  
THIRD PRONG IS PROVIDED FOR YOUR SAFETY. IF THE PROVIDED PLUG DOES NOT FIT INTO  
YOUR OUTLET, CONSULT AN ELECTRICIAN FOR REPLACEMENT OF THE OBSOLETE OUTLET.  
10. PROTECT THE POWER CORD FROM BEING WALKED ON OR PINCHED PARTICULARLY AT  
PLUGS, CONVENIENCE RECEPTACLES AND THE POINT WHERE THEY EXIT FROM THE  
APPARATUS.  
11. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.  
12. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE SPECIFIED  
BY THE MANUFACTURER, OR SOLD WITH THE APPARATUS. WHEN A  
CART IS USED, USE CAUTION WHEN MOVING THE CART/APPARATUS  
COMBINATION TO AVOID INJURY FROM TIP-OVER.  
13. UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN  
UNUSED FOR LONG PERIODS OF TIME.  
14. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL. SERVICING IS REQUIRED WHEN  
THE APPARATUS HAS BEEN DAMAGED IN ANYWAY, SUCH AS POWER-SUPPLY CORD OR PLUG  
IS DAMAGED, LIQUID HAS BEEN SPILLED OR OBJECTS HAVE FALLEN INTO THE APPARATUS,  
THE APPARATUS HAS BEEN EXPOSED TO RAIN OR MOISTURE, DOES NOT OPERATE  
NORMALLY OR HAS BEEN DROPPED.  
15. THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO  
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON APPARATUS.  
16. MAIN PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY OPERABLE  
DURING INTENDED USE. IN ORDER TO DISCONNECT THE APPARATUS FROM THE MAINS  
COMPLETELY, THE MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET  
OUTLET COMPLETELY.  
CAUTION:  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT.  
FULLY INSERT.  
2
 
FCC NOTICE  
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A RADIO  
RECEIVER, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO  
PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL  
INSTALLATION. THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO FREQUENCY  
ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY  
CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.  
HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR  
INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR  
TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND  
ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE  
OF THE FOLLOWING MEASURES:  
– REORIENT OR RELOCATE THE RECEIVING ANTENNA.  
– INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER.  
– CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH  
THE RECEIVER IS NEEDED.  
– CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP.  
WARNING:  
CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY  
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE  
EQUIPMENT.  
PROTECT YOUR FURNITURE!!  
THIS SYSTEM IS EQUIPPED WITH NON-SKID RUBBER ‘FEET’ TO PREVENT THE PRODUCT FROM  
MOVING WHEN YOU OPERATE THE CONTROLS. THESE ‘FEET’ ARE MADE FROM NON-MIGRATING  
RUBBER MATERIAL SPECIALLY FORMULATED TO AVOID LEAVING ANY MARKS OR STAINS ON  
YOUR FURNITURE. HOWEVER CERTAIN TYPES OF OIL BASED FURNITURE POLISHES, WOOD  
PRESERVATIVES, OR CLEANING SPRAYS MAY CAUSE THE RUBBER ‘FEET’ TO SOFTEN, AND  
LEAVE MARKS OR A RUBBER RESIDUE ON THE FURNITURE.  
TO PREVENT ANY DAMAGE TO YOUR FURNITURE WE STRONGLY RECOMMEND THAT YOU  
PURCHASE SMALL SELF-ADHESIVE FELT PADS, AVAILABLE AT HARDWARE STORES AND HOME  
IMPROVEMENT CENTERS EVERYWHERE, AND APPLY THESE PADS TO THE BOTTOM OF THE  
RUBBER ‘FEET’ BEFORE YOU PLACE THE PRODUCT ON FINE WOODEN FURNITURE.  
3
 
LOCATION OF CONTROLS  
1) DUST COVER  
2) LEFT SPEAKER  
3) DIAL SCALE  
4) TUNING KNOB  
5) FUNCTION SELECTOR (PHONO/AM/FM/FM STEREO)  
6) FM STEREO INDICATOR  
7) RIGHT SPEAKER  
8) POWER ON/OFF AND VOLUME CONTROL  
9) POWER LED INDICATOR  
10) 45 RPM ADAPTOR  
11) 33/45/78 RPM SPEED SELECTOR  
12) TONE ARM CLAMP  
13) AUTO STOP SWITCH  
14) LINE OUT SOCKET  
15) FM ANTENNA  
16) AC CORD  
CAUTION:  
THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE  
PERSONNEL.  
PRECAUTIONS FOR USE  
UNPACK ALL PARTS AND REMOVE THE PROTECTIVE MATERIAL.  
DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE.  
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL INCHES  
AROUND THE UNIT FOR VENTILATION.  
POWER CONNECTION  
1. CONNECT THE POWER CORD (16) TO A 120V AC ~ 60Hz OUTLET.  
2. TURN ON THE POWER (8) BY ROTATING THE VOLUME CONTROL CLOCKWISE UNTIL A CLICK IS HEARD.  
IF THE POWER LED INDICATOR (9) IS ON WITH RED LIGHT, IT MEANS THAT THE POWER SUPPLY IS  
NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC.  
LISTENING TO RADIO  
1. SET THE FUNCTION SELECTOR (5) TO THE DESIRED RADIO BAND (AM, FM OR FM-STEREO).  
2. TUNE TO THE REQUIRED STATION BY TURNING THE TUNING KNOB (4).  
3. ADJUST THE VOLUME CONTROL (8) TO OBTAIN THE DESIRED SOUND LEVEL.  
FM & FM-STEREO RECEPTION  
z
WHEN THE FUNCTION SELECTOR (5) IS SET TO THE “FM” POSITION, PROGRAMS ARE RECEIVED IN  
MONO MODE. IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS PREFERABLE TO RECEIVE THE  
PROGRAM IN MONO.  
z
SET THE FUNCTION SELECTOR (5) TO THE “FM-ST” POSITION FOR RECEIVING STEREO PROGRAMS.  
THE LED “ST” INDICATOR (6) WILL LIGHT UP WHEN A FM STEREO PROGRAM IS BEING RECEIVED.  
4
 
HINTS FOR BEST RECEPTION:-  
- AM: THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY  
ROTATING OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.  
- FM: THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA (15). THIS WIRE SHOULD BE TOTALLY  
UNRAVELED AND EXTENDED FOR BEST RECEPTION. IF FM RECEPTION IS WEAK TRY  
REPOSITIONING THE FM WIRE ANTENNA UNTIL YOU FIND THE STRONGEST FM SIGNAL.  
PLAYING PHONO RECORDS  
1. RAISE THE TURNTABLE DUST COVER.  
2. REMOVE THE STYLUS PROTECTOR AND RELEASE THE TONE ARM  
CLAMP (12).  
3. SET THE FUNCTION SELECTOR (5) TO “PHONO”.  
4. PLACE A RECORD ON THE TURNTABLE, OVER THE CENTER SPINDLE.  
5. SET THE SPEED SELECTOR SWITCH (11) TO 33, 45 OR 78 RPM ACCORDING TO THE RECORD  
YOU ARE PLAYING. PLACE THE INCLUDED 45 RPM ADAPTOR (10) OVER THE CENTER  
SPINDLE WHEN PLAYING 45 RPM RECORDS.  
6. MOVE THE TONE ARM TO THE BEGINNING OF THE RECORD OR TO THE  
BEGINNING OF A PARTICULAR TRACK. GENTLY LOWER THE TONE ARM  
ONTO THE RECORD TO START PLAYING.  
7. ADJUST THE VOLUME IF NEEDED. THE TURNTABLE WILL STOP  
AUTOMATICALLY WHEN THE RECORD FINISHES.  
8. TO STOP THE RECORD BEFORE IT ENDS, LIFT THE TONE ARM AND RETURN IT CAREFULLY  
ONTO THE TONE ARM CLAMP (12).  
9. REPLACE THE STYLUS PROTECTOR ON THE STYLUS WHEN NOT IN USE.  
IMPORTANT:  
I. DO NOT STOP OR TURN THE PLATTER MANUALLY.  
II. MOVING OR JARRING THE TURNTABLE WITHOUT SECURING THE TONE ARM CLAMP  
COULD RESULT IN DAMAGE TO THE TONE ARM.  
AUTO-STOP SWITCH OPERATION  
THE AUTO-STOP AREA ON SOME RECORDS MAY EXTEND BEYOND THE PRESET SETTING. AS A  
RESULT THE TURNTABLE COULD POSSIBLY STOP BEFORE THE LAST TRACK FINISHES. IF YOU  
EXPERIENCE THIS DURING PLAYBACK, SET THE AUTO-STOP SWITCH (13) LOCATED ON THE  
BACK OF THE UNIT TO THE “OFF” POSITION. THE TURNTABLE WILL NOW RUN TO THE END OF  
THE RECORD BUT WILL NO LONGER STOP AUTOMATICALLY. TO STOP THE TURNTABLE YOU WILL  
NEED TO EITHER SET THE FUNCTION SELECTOR (5) TO ANOTHER POSITION OTHER THAN  
PHONO OR RETURN THE AUTO-STOP SWITCH (13) TO THE “ON” POSITION. AFTER THE RECORD  
STOPS, LIFT AND RETURN THE TONE ARM CAREFULLY BACK ONTO THE TONE ARM CLAMP (12).  
5
 
LINE OUT OPERATION  
FOR BETTER PLAYBACK SOUND, YOU CAN CONNECT THE SB6051 TO AN EXTERNAL AUDIO  
AMPLIFIER VIA THE RCA LINE OUT JACKS LOCATED ON THE BACK PANEL. PLEASE PROCEED AS  
FOLLOWING:  
1.  
CONNECT THE “L” & “R” LINE OUT JACKS AND THE AUX IN OF YOUR AUDIO AMPLIFIER.  
(CONNECTION CABLE IS NOT INCLUDED).  
2.  
SELECT THE MUSIC SOURCE BY SETTING THE FUNCTION SELECTOR (5) TO “PHONO”, “AM”,  
“FM” OR “FM ST” AS DESIRED.  
3.  
4.  
TURN ON THE EXTERNAL AMPLIFIER.  
SOUND WILL THEN COME OUT FROM THE SYSTEM’S BUILT-IN SPEAKERS AND THE  
EXTERNAL AMPLIFIER’S SPEAKERS SIMULTANEOUSLY.  
SET THE VOLUME CONTROL (8) TO “MIN” AND ADJUST THE SOUND LEVEL USING THE  
VOLUME CONTROL ON THE EXTERNAL AMPLIFIER AS DESIRED.  
TURN THE SYSTEM AND THE EXTERNAL AMPLIFIER OFF WHEN YOU HAVE FINISHED  
LISTENING.  
5.  
6.  
7.  
UNPLUG THE CONNECTION CABLE.  
CARE AND MAINTENANCE  
CLEAN YOUR UNIT WITH A DAMP (NEVER WET) CLOTH. SOLVENT OR DETERGENT SHOULD  
NEVER BE USED.  
1.  
2.  
AVOID LEAVING YOUR UNIT IN DIRECT SUNLIGHT OR IN HOT, HUMID OR DUSTY PLACES.  
KEEP YOUR UNIT AWAY FROM HEATING APPLIANCES AND SOURCES OF ELECTRICAL  
NOISE SUCH AS FLUORESCENT LAMPS OR MOTORS.  
3.  
ALWAYS CLEAN THE OUTSIDE OF THE CABINET THOROUGHLY IF IT BECOMES WET WITH  
MOISTURE OR WATER SPLASHES. THIS WILL HELP TO PROTECT THE INTERNAL PARTS OF  
THE UNIT FROM ENTRY OF WATER AND POSSIBLE MOISTURE DAMAGE.  
STYLUS REPLACEMENT  
PLEASE REFER TO THE DIAGRAM BELOW TO REPLACE THE STYLUS.  
NO ADDITIONAL STYLUS IS SUPPLIED WITH THE SYSTEM.  
(1) Loosen the red part of stylus  
by screw driver and take out  
as diagram A and B  
(2) Replace with the new stylus  
(not included) as diagram C  
and D  
6
 
TROUBLESHOOTING GUIDE  
SHOULD YOU EXPERIENCE DIFFICULTIES IN THE USE OF THIS PLAYER PLEASE REFER TO THE  
FOLLOWING CHART OR CALL 1-800-777-5331 FOR CUSTOMER SERVICE.  
PROBLEM  
POSSIBLE CAUSE  
THE UNIT IS DISCONNECTED  
FROM THE AC OUTLET  
REMEDY  
CONNECT TO AN OUTLET.  
THE UNIT WILL NOT  
PLAY  
TRY THE UNIT ON ANOTHER  
OUTLET  
THE AC OUTLET HAS NO POWER  
POOR AM OR FM  
RECEPTION  
WEAK SIGNAL ON DISTANT  
STATIONS  
ROTATE THE CABINET FOR BEST  
RECEPTION  
UNIT ON BUT  
THERE IS LOW OR  
NO VOLUME  
THE VOLUME CONTROL HAS  
BEEN TURNED ALL THE WAY  
DOWN  
TURN THE VOLUME CONTROL TO  
A HIGHER OUTPUT  
7
 
90 DAY LIMITED WARRANTY AND SERVICE  
VALID IN THE U.S.A ONLY  
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective materials  
or factory workmanship for a period of 90 days from the date of original customer purchase and provided  
the product is utilized within the U.S.A. This warranty is not assignable or transferable. Our obligation under  
this warranty is the repair or replacement of the defective unit or any part thereof, except batteries, when it  
is returned to the SPECTRA Service Department, accompanied by proof of the date of original consumer  
purchase, such as a duplicate copy of a sales receipt.  
You must pay all shipping charges required to ship the product to SPECTRA for warranty service. If the  
product is repaired or replaced under warranty, the return charges will be at SPECTRA’s expense. There  
are no other express warranties other than those stated herein.  
This warranty is valid only in accordance with the conditions set forth below:  
1. The warranty applies to the SPECTRA product only while:  
a. It remains in the possession of the original purchaser and proof of purchase is demonstrated  
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the descriptions  
and warnings covered within the owner’s manual or non-SPECTRA approved modifications  
c. Claims are made within the warranty period  
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in compliance  
with electrical codes or SPECTRA owner’s manual specifications, or failure to provide reasonable care  
and necessary maintenance as outlined in the owner’s manual.  
3. Warranty of all SPECTRA products applies to residential use only and is void when products are used in  
a nonresidential environment or installed outside the United States.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to  
state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the unit carefully and send it  
freight prepaid to SPECTRA at the address shown below. IF THE UNIT IS RETURNED WITHIN THE  
WARRANTY PERIOD shown above, please include a proof of purchase (dated cash register receipt) so  
that we may establish your eligibility for warranty service and repair of the unit without cost. Also include a  
note with a description explaining how the unit is defective. A customer service representative may need to  
contact you regarding the status of your repair, so please include your name, address, phone number and  
email address to speed the process.  
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $40.00 to cover the cost  
of repair, handling and return postage. All out of warranty returns must be sent prepaid.  
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at  
[email protected] for updated information on the unit requiring service. In some cases the model  
you have may be discontinued, and SPECTRA reserves the right to offer alternative options for repair or  
replacement.  
SPECTRA MERCHANDISING INTERNATIONAL, INC.  
4230 North Normandy Avenue,  
Chicago, IL60634, USA.  
1-800-777-5331  
To register your product, visit the link below to enter your information.  
Printed in China  
8
 

Insignia Work Light NS 19E310A13 User Manual
ION Turntable VERTICAL VINYL User Manual
Ironman Fitness Home Gym 530e User Manual
Jabra Headphones BT325s User Manual
Jet Tools Drill JDP 15M MF User Manual
JVC Home Theater System GVT0150 008A User Manual
JVC Speaker System LVT1047 001A User Manual
JVC Stereo Receiver RX 7030VBK User Manual
King Canada Saw KC 162SSC User Manual
King Kutter Lawn Mower 999996 User Manual