Kenwood KRC 465 User Manual

CASSETTE RECEIVER  
KRC-565  
KRC-465  
KRC-365  
INSTRUCTION MANUAL  
©B64-2126-00 (M)  
Safety precautions  
IMPORTANT INFORMATION  
About the disc changer/CD player to  
be connected:  
To connect a disc changer having the "O-N"  
switch to this unit, set the "O-N" switch to "N".  
To connect a disc changer having no "O-N"  
switch to this unit, the converter cord CA-  
DS100 and/or switching adapter KCA-S210A  
are required as options.  
A disc changer doesn't work when it is  
connected without using these options.  
If a model with no "O-N" switch is connected,  
some unavailable functions and information  
that cannot be displayed are generated.  
Note that none of the KDC-C100, KDC-C302,  
C205, C705, and non-Kenwood CD changers  
can be connected.  
2WARNING  
2CAUTION  
To prevent injury or fire, take the  
following precautions:  
• Insert the unit all the way in until it is fully  
locked in place. Otherwise it may fall out of  
place when jolted.  
• When extending the ignition, battery, or  
ground wires, make sure to use automotive-  
grade wires or other wires with a 0.75mm2  
(AWG18) or more to prevent wire  
deterioration and damage to the wire  
coating.  
To prevent a short circuit, never put or leave  
any metallic objects (such as coins or metal  
tools) inside the unit.  
To prevent damage to the machine,  
take the following precautions:  
• Make sure to ground the unit to a negative  
12V DC power supply.  
• Do not open the top or bottom covers of the  
unit.  
• Do not install the unit in a spot exposed to  
direct sunlight or excessive heat or humidity.  
Also avoid places with too much dust or the  
possibility of water splashing.  
• Do not set the removed faceplate or the  
faceplate case in areas exposed to direct  
sunlight, excessive heat or humidity. Also  
avoid places with too much dust or the  
possibility of water splashing.  
To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
• If the unit starts to emit smoke or strange  
smells, turn off the power immediately and  
consult your Kenwood dealer.  
• Make sure not to get your fingers caught  
between the faceplate and the unit.  
You can damage both your unit and the CD  
changer if you connect them incorrectly.  
• Do not subject the faceplate to excessive  
shock, as it is a piece of precision  
equipment.  
• Be careful not to drop the unit or subject it to  
strong shock.  
The unit may break or crack because it  
contains glass parts.  
• Do not touch the liquid crystal fluid if the  
LCD is damaged or broken due to shock. The  
liquid crystal fluid may be dangerous to your  
health or even fatal.  
If the liquid crystal fluid from the LCD  
contacts your body or clothing, wash it off  
with soap immediately.  
• When replacing a fuse, only use a new one  
with the prescribed rating. Using a fuse with  
the wrong rating may cause your unit to  
malfunction.  
To prevent a short circuit when replacing a  
fuse, first disconnect the wiring harness.  
• Do not place any object between the  
faceplate and the unit.  
• Do not use your own screws. Use only the  
screws provided. If you use the wrong  
screws, you could damage the unit.  
— 3 —  
Safety precautions  
About Cassette tape  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get  
dirty, wipe them with a dry, soft cloth.  
Cleaning the tape head  
When there’s noise or the sound quality is bad  
during tape play the tape head maybe dirty,  
clean the tape head.  
NOTE  
• If you experience problems during  
installation, consult your Kenwood dealer.  
• If the unit does not seem to be working  
right, try pressing the reset button first. If  
that does not solve the problem, consult  
your Kenwood dealer.  
• Press the reset button if the Disc auto  
changer fails to operate correctly. Normal  
operatin should be resloved.  
Cleaning the Unit  
About Cassette tape  
If the faceplate of this unit is stained, wipe it  
with a dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain  
off with a cloth moistened with neutral  
cleaner, then wipe neutral detergent off.  
Applying spray cleaner directly to the unit may  
affect its mechanical parts. Wiping the  
• If the tape is slack tighten it.  
• If the cassette tape label is peeling off glue it  
on again.  
• Don’t use deformed cassette tape.  
• Don’t place cassette tape on the dashboard  
etc. where the temperature is high.  
• Don’t use cassette tape that’s 100 minutes  
long or longer.  
faceplate with a hard cloth or using a volatile  
liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
Reset button  
• Characters in the LCD may become difficult  
to read in temperatures below 41 ˚F (5 ˚C).  
• The illustrations of the display and the panel  
appearing in this manual are examples used  
to explain more clearly how the controls are  
used. Therefore, what appears on the display  
in the illustrations may differ from what  
appears on the display on the actual  
equipment, and some of the illustrations on  
the display may represent something  
impossible in actual operation.  
— 4 —  
General features  
Power  
Turning ON the Power  
Release button  
Press the [SRC] button.  
d
u
4
¢
AM  
FM  
Turning OFF the Power  
Press the [SRC] button for at least 1 second.  
Selecting the Source  
Press the [SRC] button.  
Source required  
Display  
Tuner  
"TUnE"  
Tape  
"TAPE"  
SRC  
CLK  
ATT / LOUD #1  
#3  
Q/AUD  
External disc  
Standby (Illumination only mode)  
"DISC"/"CD"  
"OFF"  
Volume  
Clock display  
Clock indicator  
Increasing Volume  
Press the [u] button.  
Decreasing Volume  
Press the [d] button.  
SYSTEM Q ATT indicator  
indicator  
LOUD indicator  
— 5 —  
General features  
• Each setting value is changed with the <Speaker setting> (page  
7).  
First, select the speaker type with the Speaker setting.  
• When the System Q setting is changed, the Bass, Middle, and  
Treble set in audio control replace the System Q values.  
Attenuator  
Turning the volume down quickly.  
Press the [ATT] button.  
Each time the button is pressed the Attenuator turns ON or OFF.  
When it’s ON, the "ATT" indicator blinks.  
Audio Control  
Loudness  
1 Select the source for adjustment  
Compensating for low and high tones during low volume.  
Press the [SRC] button.  
Press the [LOUD] button for at least 1 second.  
Each time the button is pressed for at least 1 second the  
Loudness turns ON or OFF.  
2 Enter Audio Control mode  
Press the [AUD] button for at least 1 second.  
3 Select the Audio item for adjustment  
Press the [FM] or [AM] button.  
When it’s ON, "LOUD" indicator is ON.  
Each time the button is pressed the items that can be adjusted  
switch as shown below.  
System Q  
4 Adjust the Audio item  
You can recall the best sound setting preset for different types of  
the music.  
Press the [4] or [¢] button.  
Adjustment Item  
Display  
Range  
1 Select the source to set  
Bass level  
Middle level  
Treble level  
Balance  
"BAS"  
"MID"  
"TRE"  
"BL"  
–8 — 8  
–8 — 8  
–8 — 8  
L15 — R15  
R15 — F15  
Press the [SRC] button.  
2 Select the Sound type  
Press the [Q] button.  
Fader  
"FD"  
Each time the button is pressed the sound setting switches.  
Sound setting  
Display  
5 Exit Audio Control mode  
Press the [AUD] button.  
Flat  
Rock  
Top 40  
Pops  
Jazz  
Easy  
"SQ-1"  
"SQ-2"  
"SQ-3"  
"SQ-4"  
"SQ-5"  
"SQ-6"  
"SCAn"  
Scan of Flat — Easy  
— 6 —  
Speaker Setting  
Adjusting Clock  
Fine-tuning so that the System Q value is optimal when setting  
the speaker type.  
1 Select the clock display  
Press the [CLK] button.  
1 Enter Standby  
2 Enter clock adjustment mode  
Press the [CLK] button for at least 2 seconds.  
The clock display blinks.  
Press the [SRC] button.  
Select the "OFF" display.  
2 Enter Speaker Setting mode  
3 Adjust the hours  
Press the [Q] button.  
Press the [FM] or [AM] button.  
3 Select the Speaker type  
Adjust the minutes  
Press the [4] or [¢] button.  
Press the [4] or [¢] button.  
Each time the button is pressed the setting switches as shown  
below.  
4 Exit clock adjustment mode  
Press the [CLK] button.  
Speaker type  
Display  
OFF  
"SP-F"  
"SP-O"  
"SP-6"  
"SP-5"  
For the OEM speaker  
For 6 & 6x9 in. speaker  
For 5 & 4 in. speaker  
DSI (Disabled System Indicator)  
A red indicator will blink on the unit after the faceplate is  
removed, warning potential thieves.  
4 Exit Speaker Setting mode  
Press the [Q] button.  
1 Turn the power OFF  
Press the [SRC] button for at least 1 second.  
2 Set the DSI  
While pressing the [#1] and [#3] button, press the [SRC]  
button.  
Each time the step 1 and 2 operation is done the DSI turns ON or  
OFF.  
Clock Display  
Press the [CLK] button.  
Each time the button is pressed the clock display turns ON or  
OFF.  
When it’s ON, the clock indicator is ON.  
— 7 —  
General features  
Tuner features  
Theft Deterrent Faceplate  
The faceplate of the unit can be detached and taken with you,  
helping to deter theft.  
FM/CRSC  
4
¢
AM  
Removing the Faceplate  
Press the Release button.  
The faceplate is unlocked, allowing you to detach it.  
• The faceplate is a precision piece of equipment and can be  
damaged by shocks or jolts. For that reason, keep the faceplate in  
its special storage case while detached.  
• Do not expose the faceplate or its storage case to direct sunlight  
or excessive heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
Reattaching the Faceplate  
AUTO/AME  
SRC  
#1 – 6  
1 Align the projections on the unit with the grooves on the  
faceplate.  
CRSC indicator  
Band display Preset station number  
2 Push the faceplate in until it clicks.  
The faceplate is locked in place, allowing you to use the unit.  
AUTO indicator  
ST indicator  
Frequency display  
— 8 —  
Tuning Mode  
Station Preset Memory  
Choose the tuning mode.  
Putting the station in the memory.  
Press the [AUTO] button.  
Each time the button is pressed the Tuning mode switches as  
shown below.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Select the frequency to put in the memory  
Tuning mode  
Display  
Operation  
Press the [4] or [¢] button.  
Auto seek  
"AUTO 1"  
indicator  
"AUTO 2"  
indicator  
Automatic search for a station.  
3 Put the frequency in the memory  
Preset station  
seek  
Manual  
Search in order of the stations  
in the Preset memory.  
Normal manual tuning control.  
Press the [#1] — [#6] button for at least 2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the memory on each [#1]  
— [#6] button.  
Tuning  
Selecting the station.  
Auto Memory Entry  
Putting stations with good reception in the memory  
automatically.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUnE" display.  
1 Select the band for Auto Memory Entry  
Press the [FM] or [AM] button.  
2 Select the band  
2 Open Auto Memory Entry  
Press the [FM] or [AM] button.  
Press the [AME] button for at least 2 seconds.  
When 6 stations that can be received are put in the memory  
Auto Memory Entry closes.  
Each time the [FM] button is pressed it switches between the  
FM1, FM2, and FM3 bands.  
3 Tune up or down band  
Press the [4] or [¢] button.  
Preset Tuning  
During reception of stereo stations the "ST" indicator is ON.  
Calling up the stations in the memory.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Call up the station  
Press the [#1] [#6] button.  
— 9 —  
Tuner features  
Cassette player features  
CRSC (Clean Reception System Circuit)  
Temporarily have reception switched from stereo to mono to  
reduce multi-path noise when listening to the FM station.  
2 3  
0
4
¢
AM  
FM  
Press the [CRSC] button for at least 1 second.  
Each time the button is pressed CRSC turns ON or OFF.  
When it's ON, the CRSC indicator is ON.  
Frequency Step Setting  
Changing the tuning frequency step.  
The original setting is FM band 50 kHz, and AM band 9 kHz.  
B.S  
SRC  
REP  
1 Turn the power OFF  
Press the [SRC] button for at least 1 second.  
2 Switch the frequency step  
While pressing the [#1] and [#5] button, press the [SRC]  
button.  
The frequency step changes to FM band 200 kHz, and AM band  
10 kHz.  
B.S indicator  
REP indicator  
• When the same operation is repeated, it returns to the original  
setting.  
• When the frequency step is switched, the frequencies in the  
memory are deleted.  
— 10 —  
Playing Cassette Tapes  
Blank Skip  
Fast forwarding automatically when an unrecorded portion  
continues for at least 10 seconds.  
When the Cassette Tape is inserted  
Press the [SRC] button.  
Select the "TAPE" display.  
Press the [B.S] button.  
Each time the button is pressed the Blank Skip turns ON or OFF.  
When it's ON, the "B.S" indicator is ON.  
When you want to listen to the reverse side  
Press the [23] button.  
Eject the Cassette Tape  
Press the [0] button.  
Music Repeat  
Repeating the present song.  
Press the [REP] button.  
Each time the button is pressed the Music Repeat turns ON or  
OFF.  
Fast Forwarding and Rewinding  
Fast Forwarding  
Press the [FM] button.  
When it's stopped press the [23] button.  
When it's ON, the "REP" indicator is ON.  
Rewinding  
Press the [AM] button.  
When it's stopped press the [23] button.  
Tape Advance  
Skipping to the next song or the start of the current song.  
Skipping to the next song  
Press the [¢] button.  
Skips to the start of the current song  
Press the [4] button.  
— 11 —  
External disc control features  
Playing External Disc  
Playing discs set in the optional accessory disc player connected  
to this unit.  
DISC+  
38  
DISC–  
4
¢
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
Display  
Disc player  
"CD"  
CD player  
"DISC"  
"DISC"  
CD changer  
MD changer  
Pause and play  
Press the [38] button.  
Each time the button is pressed it pauses and plays.  
SCAN RDM REP  
M.RDM  
SRC  
Disc #10 is displayed as "0".  
• The functions that can be used and the information that can be  
displayed will differ depending on the external disc players being  
connected.  
Track time  
SCN indicator  
Disc number  
Fast Forwarding and Reversing  
Fast Forwarding  
Hold down on the [¢] button.  
Release your finger to play the disc at that point.  
Track number  
Reversing  
RDM indicator  
REP indicator  
Hold down on the [4] button.  
Release your finger to play the disc at that point.  
— 12 —  
Track Search  
Random Play  
Selecting the song you want to hear.  
Press the [4] or [¢] button.  
Playing all the songs on the disc in random order.  
Press the [RDM] button.  
Each time the button is pressed Random Play turns ON or OFF.  
When it's ON, the "RDM" indicator is ON and the track number  
blinks.  
Album Search (Function of disc changer)  
Selecting the disc you want to hear.  
When the [¢] button is pressed, the next song select starts.  
Press the [DISC–] or [DISC+] button.  
Magazine Random Play  
(Function of disc changer)  
Track/Album Repeat  
Play the songs on all the discs in the disc changer in random  
order.  
Replaying the song/disc you're listening to.  
Press the [REP] button.  
Press the [M.RDM] button.  
Each time the button is pressed the Repeat Play switches as  
Each time the button is pressed the Magazine Random Play turns  
shown below.  
ON or OFF.  
Repeat play  
Display  
When it's ON, the "RDM" indicator is ON and the track and disc  
number blink.  
Track Repeat  
Album Repeat  
"REP" indicator & Track No. blink.  
"REP" indicator & Disc No. blink.  
(Function of disc changer)  
OFF  
When the [¢] button is pressed, the next song select starts.  
Track Scan  
Playing the first part of each song on the disc you are listening  
to and searching for the song you want to listen to.  
1 Start Track Scan  
Press the [SCAN] button.  
"SCN" indicator is ON.  
2 Release it when the song you want to listen to is played  
Press the [SCAN] button.  
— 13 —  
Basic Operations of remote  
Accessory of the KRC-565  
Loading and Replacing the battery  
Use one lithium battery (CR2025).  
Insert the batteries with the + and – poles aligned properly,  
following the illustration inside the case.  
4/¢  
FM/AM/DISC+/DISC–  
38  
2WARNING  
Store unused batteries out of the reach of children. Contact a doctor  
immediately if the battery is accidentally swallowed.  
Do not set the remote on hot places such as above the dashboard.  
ATT  
VOL.  
Basic operations  
SRC  
[VOL.] buttons  
Adjusting the volume.  
[SRC] button  
Each time the button is pressed the source switches.  
For the source switching order refer to <Selecting the Source>  
(page 5).  
[ATT] button  
Turning the volume down quickly.  
When it is pressed again it returns to the previous level.  
— 14 —  
In Tuner source  
In Disc source  
[FM]/ [AM] buttons  
Select the band.  
[4]/ [¢] buttons  
Doing track forward and backward.  
Each time the [FM] button is pressed it switches between the  
FM1, FM2, and FM3 bands.  
[DISC+]/ [DISC–]buttons  
Doing album forward and backward.  
[4]/ [¢] buttons  
Tune up or down band.  
[38] button  
Each time the button is pressed the song pauses and plays.  
In Cassette tape source  
[4]/ [¢] buttons  
Do <Tape Advance)> (page 11).  
[38] button  
Plays the reverse side of the tape.  
[FM ] button  
Fast forwards the tape.  
When the [38] button is pressed it releases.  
[AM] button  
Rewinds the tape.  
When the [38] button is pressed it can be released.  
— 15 —  
Accessories  
External view  
External view  
......... Number of items  
2WARNING  
......... Number of items  
If you connect the ignition wire (red) and the battery wire (yellow)  
to the car chassis (ground), you may cause a short circuit, that in  
turn may start a fire. Always connect those wires to the power  
source running through the fuse box.  
1
2
3
4
.........4  
.........4  
.........1  
.........2  
2CAUTION  
• If your car's ignition does not have an ACC position, connect the  
ignition wires to a power source that can be turned on and off  
with the ignition key. If you connect the ignition wire to a power  
source with a constant voltage supply, as with battery wires, the  
battery may die.  
• If the console has a lid, make sure to install the unit so that the  
faceplate will not hit the lid when closing and opening.  
• If the fuse blows, first make sure the wires aren’t touching to  
cause a short circuit, then replace the old fuse with one with the  
same rating.  
• Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps on  
the ends of the unconnected wires or the terminals.  
• Connect the speaker wires correctly to the terminals to which  
they correspond. The unit may be damaged or fail to work if you  
share the - wires or ground them to any metal part in the car.  
• When only two speakers are being connected to the system,  
connect the connectors either to both the front output terminals  
or to both the rear output terminals (do not mix front and rear).  
For example, if you connect the + connector of the left speaker  
to a front output terminal, do not connect the - connector to a  
rear output terminal  
5
.........1  
The use of any accessories except for those provided might result in  
damage to the unit. Make sure only to use the accessories shipped with  
the unit, as shown above.  
Installation Procedure  
1. To prevent a short circuit, remove the key from the ignition and  
disconnect the - battery.  
2. Make the proper input and output wire connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
• After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
4. Connect the wiring harness wires in the following order: ground,  
battery, ignition.  
5. Connect the wiring harness connector to the unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
— 16 —  
Connecting Wires to Terminals  
2 KENWOOD disc changer control input  
Rear left output (White) 23  
To connect the Disc changer,  
consult your Disc changer  
manual. 3  
Front left output (White)  
(KRC-565 only) 26  
FM/AM antenna input 1  
Fuse (10A)  
24  
Front right output (Red)  
(Red) (KRC-565 only) 27  
Wiring harness  
(Accessory1)25  
Rear right output (Red) 28  
If no connections are made, do not let the wire come out from the tab.  
4
29  
White/Black  
5 When using the optional power amplifier,  
To front left  
P.CONT  
connect to its power control terminal.  
speaker 30  
FRONT • L  
Power control wire (Blue/White) 15  
White  
31  
7 Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for  
the booster amplifier of the film-type antenna.  
32  
Gray/Black  
ANT.  
CONT.  
Motor antenna control wire (Blue)  
17  
To front right  
speaker 33  
FRONT • R  
Gray  
Ignition key  
switch  
10  
34  
35  
Green/Black  
To rear left  
ACC 13  
speaker 36  
REAR • L  
Ignition wire (Red) 20  
Green  
37  
38  
Purple/Black  
Car fuse box  
Battery wire (Yellow) 21  
(Main fuse)  
11  
Car fuse  
box 14  
To rear right  
speaker 39  
REAR • R  
Purple  
40  
Ground wire (Black) · (To car chassis) 22  
+
Battery 12  
— 17 —  
Installation  
Installation  
Installing in Japanese-Made Cars  
1 Refer to the section "Removing the hard rubber frame" (page 19)  
Firewall or metal support  
and then remove the hard rubber frame.  
2 Align the holes in the unit (two locations on each side) with the  
vehicle mounting bracket and secure the unit with the accessory  
screws.  
Screw (M4X8)  
(commercially  
available)  
N
T
8 mm  
8mm  
MAX.  
MAX.  
N
T/N  
3
T
4
ø5mm  
ø5mm  
Bend the tabs of the  
mounting sleeve  
with a screwdriver or  
similar utensil and  
attach it in place.  
T: Toyota cars  
N: Nissan cars  
Accessory3...for Nissan car  
Accessory4 ...for Toyota car  
• During installation, do not use any screws except for those provided.  
The use of different screws might result in damage to the main unit.  
• Damage may occur if a screwdriver or similar tool is used with  
excessive force during the installations.  
Metal mounting strap  
(commercially available)  
Self-tapping screw  
(commercially available)  
Make sure that the unit is installed securely in place. If the unit is  
unstable, it may malfunction (for example, the sound may skip).  
Screwing the Faceplate on the Unit  
If you want to fasten the  
faceplate to the main unit so  
that it does not fall off,  
screw in the provided screw  
(ø4 X 16 mm) in the hole  
shown below.  
Accessory5  
Never insert the taptite screw (ø4 × 16 mm) in any other screw hole  
than the one specified. If you screw it in another hole, it will contact  
and may cause damage to the mechanical parts inside the unit.  
— 18 —  
Removing the hard rubber frame  
Removing the Unit  
1 Refer to the section “Removing the hard rubber frame” and then  
1 Engage the catch pins on the removal tool and remove the two  
locks on the lower level.  
remove the hard rubber frame.  
Lower the frame and pull it forward as shown in the figure.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots on each side,  
as shown.  
Catch  
Lock  
Accessory2  
Screw (M4X8)  
Removal tool  
(commercially  
available)  
Accessory2  
Removal tool  
2 When the lower level is removed, remove the upper two  
locations.  
4 Lower the removal tool  
toward the bottom, and pull  
out the unit halfway while  
pressing towards the inside.  
Be careful to avoid injury from  
the catch pins on the removal  
tool.  
5 Pull the unit all the way out  
with your hands, being  
careful not to drop it.  
The frame can be removed from the top side in the same manner.  
— 19 —  
Troubleshooting Guide  
What might seem to be a malfunction in your unit may  
just be the result of slight misoperation or miswiring.  
Before calling service, first check the following table  
for possible problems.  
? The sound quality is poor or distorted.25  
One of the speaker wires is being pinched by a screw in the car.  
Check the speaker wiring.  
The tape head is dirty.26  
Clean the tape head.  
General  
The speakers are not wired correctly.27  
Reconnect the speaker wires so that each output terminal is  
connected to a different speaker.  
? The power does not turn ON.01  
The fuse has blown.  
After checking for short circuits in the wires, replace the fuse with  
one with the same rating.  
? The Touch Sensor Tone doesn’t sound.34  
The preout jack is being used.  
The Touch Sensor Tone can’t be output from the preout jack.  
No ACC position on vehicle ignition.02  
Connect the same wire to the ignition as the battery wire.  
Tuner source  
? Nothing happens when the buttons are pressed.04  
The computer chip in the unit is not functioning normally.  
? Radio reception is poor.39  
Press the reset button on the unit (page 4).  
The car antenna is not extended.  
Pull the antenna out all the way.  
? There’s a source you can’t switch.05  
The antenna control wire is not connected.40  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
There’s no tape inserted.  
Set the media you want to listen to. If there’s no media in this  
unit, you can't switch to each source.  
The Disc changer isn’t connected.08  
Connect the Disc changer. If the Disc changer isn’t connected to  
it's input terminal, You can't switch to an external disc source.  
Cassette tape source  
? Can’t remove tape.44  
The cause is that more than 10 minutes has elapsed since the vehicle  
ACC switch was turned OFF.  
? The memory is erased when the ignition is turned OFF.10  
The battery wire has not been connected to the proper terminal.  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
The tape can only be removed within 10 minutes of the ACC  
switch being turned OFF. If more than 10 minutes has elapsed,  
turn the ACC switch ON again and press the Eject button.  
The ignition and battery wire are incorrectly connected.11  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
? The Tape Advance and Music Repeat don’t operate correctly.45  
The space between the songs on the tape can’t be recognized  
because it’s too short.  
? No sound can be heard, or the volume is low.20  
Have at least 4 seconds between songs.  
The fader or balance settings are set all the way to one side.  
Center the fader and balance settings.  
The space between songs can’t be recognized because there’s too  
much noise between songs.46  
The input/output wires or wiring harness are connected incorrectly.22  
Reconnect the input/output wires or the wiring harness correctly.  
See the section on "Connecting Wires to Terminals".  
Reduce the noise between songs.  
? The blank skip doesn’t work.47  
Because noise is too loud, the non-recorded part can’t be recognized.  
The cassette tape is bad.23  
Try playing another cassette tape. If works fine, the first tape was  
Reduce the noise between songs.  
bad.  
— 20 —  
? Blank Skip functions at places that are recorded.48  
?Track Search can't be done.66-2  
Because the recording level is low, it’s recognized as not recorded.  
For the albums first or last song.  
Turn Blank Skip OFF.  
For each album, Track Search can't be done in the backward  
direction for the first song or in the forward direction for the last  
song.  
Disc source  
? "AVin" is displayed without achieving External disc control mode.50  
If the following situations, consult your nearest service  
center:  
O-N switch is set to "O" side.  
Set the switch to "N" side.  
• Even though the disc changer is connected, the Disc Changer source is  
not ON, with "AVin" showing in the display during the Changer Mode.  
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87,  
KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the  
Auxiliary input is entered when switching modes.  
Unsupported disc changer is connected.51  
Connect the supported disc changer. (page 3)  
? The specified disc does not play, but another one plays instead.52  
The specified CD is quite dirty.  
Clean the CD.  
The CD is upside-down.53  
Load the CD with the labeled side up.  
The disc is loaded in a different slot from that specified.54  
Eject the disc magazine and check the number for the specified  
disc.  
The disc is severely scratched.55  
Try another disc instead.  
? The specified track will not play.58  
Random play or magazine random play has been selected.  
Turn off random play or magazine random play.  
? Track repeat, disc repeat, track scan, random play, and magazine  
random play start by themselves.59  
The setting is not canceled.  
The settings for these functions remain on until the setting to off  
or the disc ejected, even if the power is turned off or the source  
changed.  
? Cannot play CD-R or CD-RW.60  
Finalization processing is not being conducted for CD-R/CD-RW.  
Conduct finalization processing with CD recorder.  
A non-compatible CD changer is being used to play the CD-R/CD-  
RW.61  
Use a CD changer compatible with CD-R/CD-RW to play.  
— 21 —  
Troubleshooting Guide  
E-0d:  
The protective circuit in the unit activates when the  
temperature inside the automatic disc changer  
exceeds 60°C (140°F), stopping all operation.E0d  
Cool down the unit by opening the windows or  
turning on the air conditioner. As the temperature  
falls below 60°C (140°F), the disc will start playing  
again.  
The following messages are displayed when your  
system condition.  
E-01:  
No disc magazine has been loaded in the changer.  
The disc magazine is not completely loaded.  
Load the disc magazine properly.E01  
No CD in the unit.  
Insert the CD.  
LOAd:  
Discs are being exchanged in the Disc changer.E57  
E-02:  
E-04:  
No disc has been loaded in the disc magazine.E02  
Load a disc into the disc magazine.  
23 (Blink):  
The tape player section is not operating properly.E60  
Reinsert the Tape. If the tape cannot be ejected or  
the display continues to flash even when the tape  
has been properly reinserted, please switch off the  
power and consult your nearest service center.  
No disc has been loaded in the disc magazine.E04  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-down. The CD  
is scratched a lot.  
Clean the CD and load it correctly.  
E-10:  
E-11:  
Nothing has been recorded on the MD.E10  
No tracks are recorded on the MD, although it has a  
title.E11  
E-30:  
E-77:  
The faceplate of the slave unit being connected to  
this unit has been removed.  
Replace it.E30  
The unit is malfunctioning for some reason.E77  
Press the reset button on the unit. If the "E- 77"  
code does not disappear, consult your nearest  
service center.  
E-99:  
Something is wrong with the disc magazine. Or the  
unit is malfunctioning for some reason.E99  
Check the disc magazine. And then press the reset  
button on the unit. If the "E-99" code does not  
disappear, consult your nearest service center.  
— 22 —  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
Audio section  
Frequency range (50 kHz space) ...............87.5 MHz –108.0 MHz  
(200 kHz space) .............87.9 MHz –107.9 MHz  
Maximum output power.................................................45 W x 4  
Full Bandwidth Power (at less than 1% THD) ................22 W x 4  
Tone action  
Usable sensitivity (S/N = 30dB) ...................9.3 dBf (0.8 µV/75 )  
Quieting Sensitivity (S/N = 50dB) ..............15.2 dBf (1.6 µV/75 )  
Frequency response ( 3 dB).................................30 Hz – 15 kHz  
Signal to Noise ratio (MONO)..............................................70 dB  
Selectivity ( 400 kHz).......................................................80 dB  
Stereo separation (1 kHz) ....................................................40 dB  
Bass : ...............................................................100 Hz 10 dB  
Middle : ..............................................................1 kHz 10 dB  
Treble : .............................................................10 kHz 10 dB  
Preout level / Load (during disc play) .................1800 mV / 10 kΩ  
Preout impedance............................................................600 Ω  
AM tuner section  
General  
Frequency range (9 kHz space) .....................531 kHz – 1611 kHz  
(10 kHz space) ...................530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)  
Operating voltage (11 – 16V allowable) ..............................14.4 V  
Current consumption.............................................................10 A  
Installation Size (W x H x D) ..........................182 x 53 x 152 mm  
Weight ................................................................................1.3 kg  
Cassette player section  
Tape Speed...............................................................4.76 cm/sec.  
Wow & Flutter (WRMS) ....................................................0.08 %  
Frequency response ( 3 dB) (120 µs)....................30 Hz – 14 kHz  
Separation (1 kHz) ...............................................................43 dB  
Signal to Noise ratio ............................................................57 dB  
— 23 —  

Motorola MOTO WX290 User Manual
Motorola MOTO 68000202973 B User Manual
Kenwood KRC 565 User Manual
Hitachi Travelstar HTS725016A9A364 User Manual
Dual XDM6220 User Manual
DeLonghi CC80 User Manual
Centon electronic DataStick Pro Plus DSPP8GB 001 User Manual
Centon electronic DataStick Bolt 16GBDSB RED User Manual
ALCATEL Mobile Phones OT 355 User Manual
ABB ACQ 580 04 R10 User Manual